manualshive.com logo in svg

Liftsafe Fall Protection RoofGuard HG-KIT-08, User Instruction Manual

Share
Download
Liftsafe Fall Protection RoofGuard HG-KIT-08 User Instruction Manual Download Page 23

11.0 LIFTSAFE FALL PROTECTION 

WARRANTY 

Equipment offered by Liftsafe Fall Protection (LFP) is warranted 

against factory defects in workmanship and materials for a 

period of one year from date of installation or use by the owner, 

provided that this period shall not exceed 18 months from date 

of shipment. Upon notice in writing, LFP will promptly repair or 

replace all defective items. LFP reserves the right to elect to have 

any defective item returned to its plant for inspection before 

making a repair or replacement. This warranty does not cover 

equipment damages resulting from abuse, damage in transit, or 

other damage beyond the control of LFP. This warranty applies 

only to the original purchaser, and is the only one applicable to 

our products, and is in lieu of all other warranties, expressed or 

implied.  

Page 23

Summary of Contents for RoofGuard HG-KIT-08





























Reviews:

No comments

Brands by name

Popular brands

Load more brands