background image

 

 

 
Basic Function Introduction 
 

1.  Soft start, soft stop 
2.  Minimize start-up load on garage door opener and garage door  
3.  Opening & closing force self-learning 
4.  Overloading force detecting, the door will reverse more than 15 cm automatically when it is 

overloaded when closing and will stop when it is overloaded when opening.  

5.  Safety resistance adjustable, with a wide range, sensitive and reliable. 
6.  Low-voltage protection, the process will not perform any action of opening and closing when voltage 

is too low, door panel and controller won’t be damaged. 

7.  Rolling code frequency 
8.  Auto -closing feature. 

a.  NOTE: It is compulsory to install a photo electric beam if auto close ode is 

selected, otherwise    the door may cause personal injury or damage to 
property. Auto close time is adjustable. 

 

9.  Metal chassis  
10.  Backup battery interface available, in case of power failure. 
11.  Wall switch interface available. 
12.  O/S/C button 

B

, make adjustments, maintenance and emergency opening or closing easier. 

  

     

 

 

 

 

 

 

 
            
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for LA-SDO1





















Reviews: