Life Fitness LS 9100 Service Manual Download Page 44

Page: 44 / 93

Tools Required:

3/8 inch wrench or 3/8 inch socket.

Step 1

Turn the power OFF. Disconnect the power cord from the outlet.

Step 2

Remove the HOUSING. (See “How To...”)

Step 3

Prop up the (2) PEDAL LEVERS to relieve the tension from the belt.

Step 4

Using a 3/8 socket or wrench remove the (4) retainer bolts and remove the retainers brackets from each side.

Step 5

Carefully slide belt off of the clutch assemblies, through the pedal arm and the lower pulleys to remove.

Step 6

Reverse steps 1 through 7 to install new drive belt and secure shrouds.

Life Fitness 9100/9500HR Belt Drive Stairclimbers

How To… REMOVE AND REPLACE MONOCOLUMN

Tools Required:

5/32” Hex key wrench, 7/32” Hex key wrench, 9/16” Wrench, Light hammer, Center punch

Retainer Bracket

Drive Belt

Clutch

Arm Pulley

Retainer Bolts

Summary of Contents for LS 9100






























































































Search results

Summary of Contents for LS 9100

Reviews:

Related manuals for LS 9100

Brands by name

Popular brands

Life Fitness LS 9100, Service Manual

Search results

Summary of Contents for LS 9100

Reviews:

Related manuals for LS 9100

Brands by name

Popular brands