Life Fitness LS 9100 Service Manual Download Page 21

Page: 21 / 93

Life Fitness 9100/9500HR Belt Drive Stairclimbers

TROUBLESHOOTING GUIDE

Symptom: NO HEART RATE OR DISPLAY READOUT

Symptom

Probable Cause

Corrective Action

No heart rate

Faulty cable connection

Verify heartrate cable is properly connected.

Using an ohmmeter, verify continuity at the
main console cable. See wiring diagram for pin
location.

Replace faulty cable.

Life Pulse handlebar

Verify Lifepulse that handlebars are functioning.
See diagnostic.

Using an ohmmeter, verify continuity between
Lifepulse sensor and cable connection. See
wiring diagram.

Replace handlebar assembly.

Heartrate (DSP) Board

Verify the heartrate (DSP) board is
communicating. See Diagnostic.

Replace faulty heartrate (DSP) board.

Lifepulse sensor molding
loose

Cleaning solution that contains
an acid or ammonia base

Replace Lifepulse Sensor Kit.

For Assistance Contact
Life Fitness Customer Support Services
Teleph.: 847.451.0036 or 800.351.3737
Telefacs.: 847.288.3702 or 800.216.8893

Summary of Contents for LS 9100






























































































Search results

Summary of Contents for LS 9100

Reviews:

Related manuals for LS 9100

Brands by name

Popular brands

Life Fitness LS 9100, Service Manual

Search results

Summary of Contents for LS 9100

Reviews:

Related manuals for LS 9100

Brands by name

Popular brands