Life Fitness LS 9100 Service Manual Download Page 14

Page: 14 / 93

Life Fitness 9100/9500HR Belt Drive Stairclimbers

TROUBLESHOOTING GUIDES

Symptom: ERRATIC DISPLAY CONSOLE LED’s.

Symptom

Probable Cause

Corrective Action

Display Console LED’s are
not constant

AC Line cord not plugged into
electrical wall outlet

Plug the AC Line cord into proper electrical
outlet.

Unit power switch (I/O) not in
ON position

Place the power switch in ON (I) position.

Power supply outlet 115VAC

Using a voltmeter, verify power supply is
115VAC.

Loose wire connections, or
wire connectors not seated
properly

Disconnect then reconnect harness
connections at the Display Console. See How
To... Remove Display Console.

Disconnect then reconnect all connections. See
How To... Remove the Shroud Assembly.

Damage cable

Using an ohmmeter, verify continuity of wire
harness. Replace the worn or damaged wire
harness.

Display Console

Perform Display Test see diagnostic.

Using a voltmeter, verify power at the cable and
Display Console connection. See wiring
diagram for pin location.

Replace faulty display.

For Assistance Contact
Life Fitness Customer Support Services
Teleph.: 847.451.0036 or 800.351.3737
Telefacs.: 847.288.3702 or 800.216.8893

Summary of Contents for LS 9100






























































































Search results

Summary of Contents for LS 9100

Reviews:

Related manuals for LS 9100

Brands by name

Popular brands

Life Fitness LS 9100, Service Manual

Search results

Summary of Contents for LS 9100

Reviews:

Related manuals for LS 9100

Brands by name

Popular brands