Life Fitness Exercise Bike Lifecycle 8500 Assembly Instructions Manual Download

Page: 19 / 35

STEP 19:

FIGURE 19

•

Insert the two GUIDE RODS (19) into the BASE (25) as shown in FIGURE 19. Lubricate the GUIDE RODS (19) with a slicon or teflon

spray that is available at most hardware stores.

• Slide two WEIGHT STACK CUSHIONS (47) down over the GUIDE RODS (19). See FIGURE 19.

•

Using

EXTREME CARE

slide twenty WEIGHT PLATES (106) down over the GUIDE RODS (19) with the the key-hole facing as

shown in FIGURE 19.

•

SECURELY

assemble the WEIGHT STACK SHAFT (50) to the HEAD PLATE (53) using one 3/8 X 1-1/4” BOLT (88) and one 3/8”

BLACK LOCK WASHER (81).

(Note:

The bolt hole in the HEAD PLATE (53) should be on top.)

•

Carefully Slide the HEAD PLATE ASSEMBLY down over the GUIDE RODS (19) onto the weight stack as shown.

• Slide two 13/16” SHAFT COLLARS (78) over the GUIDE RODS (19) as shown in FIGURE 19.

• REPEAT the above steps to assemble the weight stacks on the PRESS WEIGHT STACK BASE (24) and the LEG WEIGHT STACK

BASE (23).

(NOTE: Use four WEIGHT STACK CUSHIONS (47) (two per guide rod!) on the LEG WEIGHT STACK BASE (23)

as shown in FIGURE 19.)

TWO

PER

SIDE!

108

107

106

3/8” LOCK
WASHER 81

3/8 X 1-1/4” 88

• Apply one set of WEIGHT STACK LABELS - LBS. OR NUMBERED 1-20 (107) (108) to each WEIGHT PLATE (106). See FIGURE 19.

TWO PER SIDE

ON THIS STACK ONLY!

Summary of Contents for Exercise Bike Lifecycle 8500




































Search results

Summary of Contents for Exercise Bike Lifecycle 8500

Reviews:

Related manuals for Exercise Bike Lifecycle 8500

Brands by name

Popular brands

Life Fitness Exercise Bike Lifecycle 8500, Assembly Instructions Manual

Search results

Summary of Contents for Exercise Bike Lifecycle 8500

Reviews:

Related manuals for Exercise Bike Lifecycle 8500

Brands by name

Popular brands