LG UU24 Installation Manual Download Page 18 | Manualshive

Page: 18 / 43

background image

18

Air Conditioner

The Indoor Unit Installation

•

Insert the nuts and washer onto the

suspension bolts for locking the suspension
bolts on the ceiling.

•

Mount the suspension bolts to the anchor-

nuts firmly.

•

Secure the Installation plates onto the

Suspension bolts (adjust level roughly.)
using nuts, washers and spring washers.

•

Engage 2 hooks on the both left and right

side of the unit to the lower slot of
Installation Plates.

•

Adjust a level with a level gauge on the

direction of left-right, back-forth by adjusting
suspension bolts.

•

Move the hooks on the unit to the upper slot

of Installation Plates. Then the unit will be
declined to the bottomside so as to drain
well.

Washer

Nut

Suspension

bolts

Ceiling

Anchor nut

Suspension

bolts

Spring
washer

Max.

12mm

Washer

Nut

1)

2)

Suspension

bolt

Installation plate

Adjust a level

R

Level gauge

Lower slot

R

R

Upper slot

«
...
16
17
18
19
20
...
»

Summary of Contents for UU24












































Reviews:

No comments

Related manuals for UU24

Brand: Danby Pages: 34

Brand: Danby Pages: 40

Therapy Air Smart TAS-100

Brand: Zepter Pages: 9

SMOKEMASTER C-12

Brand: Air Quality Engineering Pages: 14

Brand: Olmo Pages: 37

Brand: Kaisai Pages: 36

Saphir comfort BT

Brand: Truma Pages: 24

Brand: Saivod Pages: 88

Brand: A.O. Smith Pages: 16

Brand: Silent Night Pages: 12

Brand: Uberhaus Pages: 24

Brand: Rowenta Pages: 44

Brand: Fakir Pages: 56

climaVAIR V 7-050 NW

Brand: Vaillant Pages: 24

Brand: Goodman Pages: 14

Brand: Seifert Pages: 23

Brand: Friedrich Pages: 28

Brand: Mistral Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands