LG STB-3000 Setup Manual Download

Page: 80 / 86

206-4272

Reference: STB Installer Remote

If you are using an LG display panel, the LG remote provided with the

display panel should be sufficient. However, if you are using a commercial

non-LG display panel or if you intend to use multiple STBs/displays in a

single room installation environment, an LG Installer Remote dedicated

to STB control (see example at right) is available for purchase.
The STB Installer Remote illustrated on the right shows typical remote

control functions and is provided for reference only.
For additional information and/or to purchase an STB Installer Remote,

please contact your LG service representative.

Installer Remote Functionality

The STB Installer Remote provides the same standard configuration

functionality as a typical LG Installer Remote, along with multi-code

capability. See also “Installer Remote Control Typical Key Functions”

information on the previous page.

Programming the STB Installer Remote (Multi-IR Code

Feature)

This section describes how to program the STB Installer Remote to send

unique IR codes based on “bed number” in a multi-STB/display single

room installation. Up to nine beds can be programmed.

Note:

The STB will always respond to the standard LG Installer Remote

IR code scheme, regardless of its multi-code IR setting.
The following procedure describes how to program the bed number in

the STB Installer Menu and in the STB Installer Remote.
1. Installer Menu item 020 FEATURE LEVEL determines the additional

IR code scheme to which the STB will respond. Access the STB

Installer Menu, and set item 020 to the desired value.

The STB Installer Remote must now be programmed to match the

FEATURE LEVEL setting. That is, if item 020 is set to 17 for Bed 2,

the STB Installer Remote must also be set to Bed 2.

Note:

In its default state, the STB Installer Remote uses the standard

LG Installer Remote IR code scheme.

2. On the STB Installer Remote, press and hold

along with the

desired (bed) number key.

The TV LED at the top left of the remote will light for three seconds

and then turn OFF.

3. Once the TV LED turns OFF, release both keys on the remote.
4. Verify the remote functionality, based on your settings.

Note:

If necessary, you can restore the default STB Installer Remote IR

code scheme by pressing and holding

on the remote along with the

“0” key.

VOL

TIMER

INPUT

SAP

DVD

MUTE

FLASHBK

VD/

EXIT

GUIDE

INFO

PORTAL

Summary of Contents for STB-3000























































































Search results

Summary of Contents for STB-3000

Reviews:

Related manuals for STB-3000

Brands by name

Popular brands

LG STB-3000, Setup Manual

Search results

Summary of Contents for STB-3000

Reviews:

Related manuals for STB-3000

Brands by name

Popular brands