LG STB-3000 Page 30 Setup Manual Download

Page: 30 / 86

206-4272

Installer Menu

Use the Installer Menu to set up, change, or view operational settings. This section describes how to

access, use, and exit the Installer Menu on location; however, you should also refer to the Installer

Menu descriptions in this document if you are configuring the STB using an FTG Configuration (.tlx)

file created using LG’s FTG File Manager software.

Refer to the table on pages 32 and 33 for brief descriptions of Installer Menu items. More detailed

descriptions follow the table listing.

Accessing the Installer Menu

1. Turn ON the STB/display panel.

If the EZ-Manager Wizard appears on the screen when you turn ON the STB/display, exit the

wizard.

2. Using an Installer Remote, press

MENU

repeatedly until the on-screen display of the setup

menus (if the STB is in Pass-through Mode) or the Function Menu (if the STB is not in

Pass-through Mode) no longer toggles, and then press the STB Installer Menu entry sequence

(e.g.,

) +

EXIT

to access the STB Installer Menu.

Note:

The default Installer Menu entry sequence is “9876”; however, if Installer Menu item 000

INSTALLER SEQUENCE has been modified, the entry sequence may be one of three additional

options. See Installer Menu detailed descriptions for further information.

The Installer Menu opens with item 000 INSTALLER SEQ 000.

Note:

If the password (entry sequence) is not entered or registered correctly, you will see the message

“ENTER STB PASSWORD 0000” at the top of the screen instead of the STB Installer Menu header.

Once you re-enter the correct password (e.g., press 9-8-7-6 + EXIT), the STB Installer Menu will display.

Note:

If an LG Hospitality TV (for example, LP645H, LT670H, etc.) is being used as the display panel

(connected to MPI/MTI TELEVISION CONTROL on the STB) and you press the TV Installer Menu entry

se OK, you will access the TV’s Installer Menu instead of the STB’s Installer Menu. The TV’s

Installer Menu is accessible as read-only.

Note:

If the STB is not in Pass-through Mode, the Installer Menu is accessible as read-only. Also,

the TV Zone # will be indicated in the Installer Menu header under the configuration mode indicator

described on the following page.

STB_3000 PTC INSTALLER MENU

CPU-CTV

000 INSTALLER SEQ 000

UPN 000-000-000-000

ASIC D279

PTC V1.00.023

CPU V3.00.71.01

Typical Installer Menu

The menu header identifies this as the

STB-3000 Installer Menu. In the Installer

Menu footer, you can see the current

software versions of the STB, as indicated.

PTC Version

CPU Version

Summary of Contents for STB-3000























































































Search results

Summary of Contents for STB-3000

Reviews:

Related manuals for STB-3000

Brands by name

Popular brands

LG STB-3000, Setup Manual

Search results

Summary of Contents for STB-3000

Reviews:

Related manuals for STB-3000

Brands by name

Popular brands