LG STB-3000 Page 6 Setup Manual Download | Manualshive

Page: 6 / 86

background image

6

206-4272

STB-3000 Introduction / Setup Checklist

Introduction

The STB-3000 set-top box is designed to be connected to a compatible commercial display panel to

create a system that can provide Pro:Centric

®

functionality, as well as either RF or IP content delivery.

The STB-3000 may be used with LG Commercial Hospitality TVs (LP645H, LT670H, etc.) that support

Multiple Protocol Interface (MPI), or the STB-3000 may be used with LG Commercial Public Display TVs

(LD450C, LT560C, etc.) or LG Commercial Monitors (M3203CCBA, M3204C, etc.) that support the

TV-Link Monitor (TLM) interface. The STB-3000 may also be used with commercial non-LG TVs that

support SONIFI’s Multiple Television Interface (MTI) protocol.

Setup Checklist

See also the STB-3000 Owner’s Manual for information on STB installation and hardware and cable

connections.

Installation and Setup

__ Unpack the STB and all accessories.

Accessories provided:

•  AC/DC Power Adapter
•  HDMI Cable
•  MPI/MTI Cable (proprietary cable for LG MPI or SONIFI MTI control of display panel)
•  TLM Cable (proprietary cable for LG TLM control of display panel)
•  A/V Adapter Cable

__ Obtain an LG Installer Remote for configuration purposes.

If you are connecting the STB to an LG display panel, the LG remote provided with the display should

be sufficient. If you are connecting the STB to a non-LG display panel or if you intend to use multiple

STBs/displays in a single room installation environment, an LG Installer Remote dedicated to STB

control is available for purchase. For additional information and/or to purchase an STB Installer

Remote, contact your LG service representative. See also Reference section, “STB Installer Remote.”

__ Determine the installation location for the STB and display panel stand or mount.
__ Determine mounting and installation requirements, for example, AC power source outlet, antenna/cable

service connectors, any external equipment required for system operation, all necessary cables, wires,

and connectors, and any other additional required hardware, etc.

__ Install the display panel on VESA mount or stand.

Note:

It may be advisable to make all cable connections before installing on VESA mount or stand.

Hardware Connections

__ Install any additional hardware as appropriate to your institution, LAN, etc.

Cable Connections

__ Make all connections to the STB jack panels, as described in this document.

Commercial Mode Setup

__ Complete appropriate procedures as described in this document for Commercial Mode operation.

«
...
4
5
6
7
8
...
»

Summary of Contents for STB-3000























































































Reviews:

No comments

Related manuals for STB-3000

Brand: Pace Pages: 29

Brand: Homecast Pages: 44

Brand: BT Pages: 27

Brand: ZaapTV Pages: 18

Brand: Hyundai Pages: 78

Brand: Pace Pages: 48

Brand: Trevi Pages: 64

Brand: FORMULER Pages: 35

Brand: Laser Pages: 12

Brand: Energy Pages: 88

Brand: Shakespeare Electronic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands