LG SRFVC2416S Owner'S Manual Download Page 55

Page: 55 / 68

TROUBLESHOOTING

ENGLISH

Water is not

dispensing.

New installation or water line recently connected.

• Dispense 2.5 gallons of water (flush for approximately 5 minutes) to remove trapped air

and contaminants from the system. Do not dispense the entire 2.5 gallon amount

continuously. Depress and release the dispenser pad for cycles of 30 seconds ON and 60

seconds OFF.

The dispenser panel is locked.

• Press and hold the

Lock

button for three seconds to unlock the control panel and

dispenser.

The dispenser is not set for water dispensing.

• The dispenser can be set for ice or water. Make certain that the control panel is set for the

proper operation.

Press

the

Water

button on the control panel to dispense water.

Refrigerator or freezer doors are not closed properly.

• Water will not dispense if any of the refrigerator doors are left open.

Water filter has been recently removed or replaced.

• After the water filter is replaced, dispense 2.5 gallons of water (flush for approximately five

minutes) to remove trapped air and contaminants from the system. Do not dispense the

entire 2.5 gallon amount continuously. Depress and release the dispenser pad for cycles of

30 seconds ON and 60 seconds OFF.

Tubing connecting refrigerator to house supply valve is kinked.

• The tubing can kink when the refrigerator is moved during installation or cleaning.

Resulting in reduced water flow. Straighten or repair the water supply line and arrange it

to prevent future kinks.

The house water supply is not connected, the valve is not turned on fully, or the valve is

clogged.

• Connect the refrigerator to the water supply and turn the water shutoff valve fully open. If

the problem persists, it may be necessary to contact a plumber.

Dispensing warm

water.

Refrigerator was recently installed.

• Allow 24 hours after installation for the water storage tank to cool completely.

The water dispenser has been used recently and the storage tank was exhausted.

• Depending on your specific model, the water storage capacity will range from

approximately 20 to 30 oz.

Dispenser has not been used for several hours.

• If the dispenser has not been used for several hours, the first glass dispensed may be

warm. Discard the first 10oz.

Refrigerator is connected to the hot water supply.

• Make sure that the refrigerator is connected to a cold water pipe.

WARNING: Connecting the refrigerator to a hot water line may damage the

icemaker.

Problem

Possible Cause & Solution

Summary of Contents for SRFVC2416S





































































Search results

Summary of Contents for SRFVC2416S

Reviews:

Related manuals for SRFVC2416S

Brands by name

Popular brands

LG SRFVC2416S, Owner'S Manual

Search results

Summary of Contents for SRFVC2416S

Reviews:

Related manuals for SRFVC2416S

Brands by name

Popular brands