LG SRFVC2416S Owner'S Manual Download Page 11

Page: 11 / 68

INSTALLATION

ENGLISH

Unpacking the Refrigerator

WARNING

• Use two or more people to move and install the

refrigerator. Failure to do so can result in back

injury or other injury.

• The refrigerator is heavy. Protect the floor when

moving the refrigerator for cleaning or service.

Always pull the refrigerator straight out when

moving it. Do not wiggle or walk the refrigerator

when trying to move it, as floor damage could

occur.

• Keep flammable materials and vapors, such as

gasoline, away from the refrigerator. Failure to

do so can result in fire, explosion, or death.

NOTE

• Remove tape and any temporary labels from

your refrigerator before using. Do not remove

any warning labels, the model and serial number

label, or the Tech Sheet that is located under the

front of the refrigerator.

• To remove any remaining tape or glue, rub the

area briskly with your thumb. Tape or glue

residue can also be easily removed by rubbing a

small amount of liquid dish soap over the

adhesive with your fingers. Wipe with warm

water and dry.

• Do not use sharp instruments, rubbing alcohol,

flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the

surface of your refrigerator.

• Reinstall or adjust shelves as needed.

Refrigerator shelves are installed in the shipping

position. Reinstall shelves according to your

individual storage needs.

Choosing the Proper

Location

Water

The refrigerator must be located where a water

supply can be connected for the automatic

icemaker.

NOTE

• The water pressure must be 20 - 120 psi or 138 -

827 kPa or 1.4 - 8.4 kgf/cm

. If the refrigerator is

installed in an area with low water pressure
(below 20 psi or 138 kPa or 1.4 kgf/cm

), you can

install a booster pump to compensate for the

low pressure.

Electricity

Use an individual, grounded outlet:115 Volts, 60

Hz, AC, 15 amps minimum.

WARNING

• Do not overload house wiring and cause a fire

hazard by plugging in multiple appliances in the

same outlet with the refrigerator.

• To reduce the risk of electric shock, do not install

the refrigerator in a wet or damp area.

Flooring

To avoid noise and vibration, the unit must be

installed and leveled on a solidly constructed floor.

If required, adjust the leveling legs to compensate

for the unevenness of the floor.

NOTE

• Installing on carpeting, soft tile surfaces, a

platform or weakly supported structure is not

recommended.

Ambient Temperature

Install this appliance in an area where the

temperature is between 55 °F (13 °C) and 110 °F

(43 °C).
If the temperature around the appliance is too low

or high, cooling ability may be adversely affected.

Summary of Contents for SRFVC2416S





































































Search results

Summary of Contents for SRFVC2416S

Reviews:

Related manuals for SRFVC2416S

Brands by name

Popular brands

LG SRFVC2416S, Owner'S Manual

Search results

Summary of Contents for SRFVC2416S

Reviews:

Related manuals for SRFVC2416S

Brands by name

Popular brands