45
206-4342
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 0 to use the default aspect ratio each time the TV is turned
ON (see item 096 DEF. ASP. RATIO). If set to 1, the aspect ratio
set before the TV was turned OFF will be the current aspect ratio
when the TV is turned ON again.
107 - BANNER SELECT
Selects the type of banner to display during channel change.
Set to 1 for Channel-Time display, plus channel information (full
banner). Set to 0 for Channel-Time display only (small banner).
116 - VIDEO MUTE EN (Video Mute Enable)
Applicable for analog channels only. If set to 1, video mutes (blank
screen) when no signal is present.
117 - FACT DEFAULT (Factory Default)
Set to 1 and press OK to restore the factory default settings of all
Installer Menu items. Once complete, the value returns to 0.
Caution:
If set to 1, this clears all Installer Menu custom
settings and restores the factory default settings. It also
clears the channel lineup, including any assigned
channel icons and custom text labels.
Note:
See also Reference section, “Restoring Factory Defaults on
the TV(s),” for further information.
118 - POWER SAVINGS
Default set to 3—the power circuitry for both the embedded
b
-LAN
module and the GAME CONTROL/MPI port is only powered when
the TV is turned ON. When the TV is turned OFF, the embedded
b
-LAN and the GAME CONTROL/MPI port are not powered.
Note that the TV must be turned ON in order to communicate with
the embedded
b
-LAN module for configuration and control when
POWER SAVINGS is set to 3. If POWER SAVINGS is set to 1, the
b
-LAN module is always powered.
Similarly, if MPI communication is required for external MPI
control, POWER SAVINGS should be set to 1 so that the GAME
CONTROL/MPI port circuitry is always powered.
Note:
See Reference section, “
b
-LAN Setup & Overview,” for
further information.
Caution: POWER SAVINGS should NEVER be set to 7.
This setting is intended for factory use only.
119 - DATA CHANNEL
Set to 0 to disable. Set from 1 to 135 to match the RF channel
number that will be used by the Pro:Centric server as its data
channel. *
For TVs in Pass-through Mode or FTG Mode via CPU, if this item
is left at its default value (255), the TV’s Data Channel Auto Search
feature will be enabled (see additional information below).
Note:
The Data Channel Auto Search feature is not available
when the TV’s EBL is in FTG Mode. If the DATA CHANNEL value
is 255 when the TV is configured for FTG Mode via EBL, DATA
CHANNEL is defaulted to 0.
Data Channel Auto Search feature: When this item is set to 255
(default), once every 24 hours, the TV will initiate a search of 10
predefined channels (10, 20, 30, ... 100) and then, if necessary,
perform a complete search of the RF channels (1 to 135) in an
attempt to find the RF channel used by the Pro:Centric server as
its data channel. If the Pro:Centric RF channel is found, the DATA
CHANNEL value will be changed from 255 to match the server’s
RF channel number. The time at which the Auto Search occurs
depends on the setting of item 121 P:C RF WAKE HR. See item
121 description for further information.
Note:
Pro:Centric updates are downloaded from the Pro:Centric
server to the TV when the TV is turned OFF. While Pro:Centric
updates are in progress, it is not possible to turn ON the TV.
121 - UPDATE TIME HR
Based on the settings of this item and item 122 UPDATE TIME MN,
the Wake For Update feature wakes the TV once daily to check for
and, if applicable, download updates from the Pro:Centric server.
Set the Wake For Update hour from 0 to 23. This item uses the
24-hour clock format. The value “128” (default) is displayed as
“OFF.” Directly entering 128 resets the default value (OFF) for this
item, though note that this setting does not mean the TV will not
initiate update events—see additional information below.
Under standard TV OFF/ON operating conditions (i.e., item 002
AC ON is set to 0), a Wake For Update event occurs when the TV
is OFF and causes the TV’s CPU to temporarily turn ON, perform
the update cycle, and then turn back OFF, all while the TV appears
to be OFF. If item 002 AC ON is set to 2, 3, 18, or 19 for Instant
ON, then the TV’s CPU is always ON and Wake For Update occurs
when the TV is in its Muted ON state (i.e., the TV only appears to
be OFF). The Wake For Update event causes the TV’s CPU to
reboot in order to perform the update cycle and then return to its
Muted ON state. See also description for item 002.
If this item is set to 128 (OFF), the time at which a Data Channel
Auto Search (item 119 set to 255) and/or an Instant ON update
(item 002 set to 2, 3, 18, or 19) occurs is determined as follows:
The TV initiates the search and/or checks for updates at 2:00
AM (if the TV clock is set) or after two hours of elapsed time from
when AC power was applied (if the TV clock is not set). If the
TV display is ON when a Wake For Update event is to occur, the
update will take place the next time the TV is turned OFF.
Installer Menu (Cont.)
*
PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.