manualshive.com logo in svg

LG Pro:Centric 24LT572M, Setup Manual, Page: 42 / 101

Share
Download
LG Pro:Centric 24LT572M Setup Manual Download Page 42

42

206-4342

Note: 

The default setting (254) is not selectable in the Installer 

Menu. If you ever need to restore the default setting, you must 

reload the factory default settings. See item 117 description and/or 

Reference section, “Restoring Factory Defaults on the TV(s),” for 

further information.

Note:

 When Hospital Mode is enabled, i.e., not set to 0, channel 

banks are applied, which means that the (Lodging) TV Zoning 

feature is not available. Channel banks are not supported if  

Hospital Mode is disabled, i.e., set to 0, or on TVs that are in FTG 

Mode via EBL, EBL-LNT Mode, or MPI-EXT Mode. If Hospital 

Mode is disabled and if the TVs are not configured in one of the 

three modes listed above (EBL-FTG, EBL-LNT, or MPI-EXT), the 

TV Zoning feature is available. See “Channel Banks Overview” 

on pages 28 to 30 and/or Reference section, “Using the TV 

Zoning Feature,” for further information. 

Note:

 In the Installer Menu, an informational code is displayed 

at the right of each Hospital Mode value. Each code consists of 

three characters. The first character—T, P, or B—identifies the 

speaker: TV, Pillow, or Both. The second character—Z, P, R, 

or D—identifies the pillow speaker code: Zenith, Philips, RCA, or 

Disabled. The third character—1 or 2—identifies the bed number.

 

In the table above, each bolded character represents an element of 

the Hospital Mode code. 

028 - CH. OVERIDE (Channel Override) 

This item either allows or restricts tuning of channels that are NOT 

in the PTC Channel Map.

 

If set to 1, end users can tune channels 

that are not in the PTC Channel Map by direct keypad entry. If  

set to 0, users are restricted to only the channels that are in the 

PTC Channel Map. In the case of CPU-CTV Mode, there are no 

channels in the PTC Channel Map; therefore, direct keypad entry 

is not available. Also, when this item is set to 0, the PTC Channel  

Map (PTC-CTV Mode)/CPU channel lineup (CPU-CTV Mode) is 

locked, and user access to channel settings in the TV setup menus 

is restricted. 

Note:

 This item is not applicable when the TV is in FTG Mode. 

029 - REMAP AUX INPUTS

 

Set to 1 to remap the PTC’s direct tune channels for Aux inputs 

from 13x to 9x. This allows 2-digit only tuning systems (i.e., 

legacy On Command Video™) to direct tune Aux inputs. See also 

Reference section, “TV Aux Input Configuration.”

030 - ACK MASK 

MPI Communication Parameter. When set to 1, enables the ACK 

feature of MPI.

031 - POLL RATE

 

MPI Communication Parameter. Selects the poll rate for MPI. Step 

size of 16 ms. Changing from default may affect communication via 

MPI.

032 - TIMING PULSE

 

MPI Communication Parameter. Sets the baud rate for MPI. Step  

size of 4.3 uS. Changing from default may affect communication 

via MPI.

035 - HDMI1 ENABLE 

Set to 1 to enable HDMI 1 input in DTV Mode. Set to 2 to enable 

HDMI 1 input in PC Mode. Set to 0 to disable display panel HDMI 

1 input. 

039 - REAR AUX EN. (Rear Aux Enable)

 

Set to 1 to enable display panel rear Aux (AV) input. Set to 0 to 

disable display panel rear Aux (AV) input. 

041 - SIMPLINK EN

Set to 0 to disable the SIMPLINK feature. Set to 1 to enable  

SIMPLINK functionality without enabling remote control access  

to the SIMPLINK Menu. Set to 2 to enable both SIMPLINK 

functionality and SIMPLINK Menu access, though note that the 

Speaker menu option will be inaccessible/grayed out. Set to 3 to 

enable all aspects of SIMPLINK feature and SIMPLINK Menu. If 

a home theater device is connected to the TV, users can select 

either the TV or HT (home theater) speaker. 

Note:

 When both this item 

and

 item 042 AUTO INPUTS are 

enabled in the Installer Menu, HDMI inputs will be detected by 

SIMPLINK, but the Auto Input(s) Sensing Feature will not function.

042 - AUTO INPUTS

Determines the Aux inputs for which auto-sensing is enabled. Set 

to 0 to disable auto-sensing for all available inputs. Set to 255 to 

enable auto-sensing for all available inputs. For information on  

options for individual input settings, see Reference section, “Auto 

Input(s) Sensing Feature.”

Note:

 In order for auto-sensing to be enabled for an input, that 

input must also be enabled in the Installer Menu. For example, to 

enable auto-sensing for HDMI 1, item 035 HDMI1 ENABLE must 

also be set to 1 or 2. Also, see note above regarding TV operation 

when both this item and item 041 SIMPLINK EN are enabled.

046 - STRT AUX SRCE (Start Aux Source)

 

Sets the starting Aux source. When turned ON, the TV will tune to 

starting Aux source if item 004 STRT CHANNEL is set to 0. 
1 = AV

3 = HDMI 1

5 = HDMI 2

255 = Last Aux

Note:

 In order for an Aux input to be selected as the starting Aux 

source, the input also must be enabled in the Installer Menu.

Note:

 This item is not available in the Installer Menu unless item 

004 STRT CHANNEL is set to 0.

Installer Menu (Cont.)

Summary of Contents for Pro:Centric 24LT572M






































































































Reviews:

No comments