LG LZ-H025GBA4 Installation Manual Download Page 14 | Manualshive

Page: 14 / 25

background image

14

Ventilator

Installation

Ceiling fixing bolt
(M10)

Nut

Washer

Spring washer

Nut

Assembly of washer, nut

Tighten the common washer and nut (more than 21mm
for the outside diameter of M10, to the commercial
ceiling fixing bolt (M10) as shown in the right figure.

• For the ceiling fixing bolt, perform work less than

50mm under the ceiling fixing bracket.

Connection of duct

After securely connect the duct with the duct connection flange, wrap it with a commercial aluminium
tape so that air cannot be leaked.

Adjust the duct from the ceiling so that no force is applied to the main body of the ventilation system.

Always use two ducts at the outdoor with the heat insulating material for prevention of dewing.

Duct

Taping

Installation of main body

«
...
12
13
14
15
16
...
»

Summary of Contents for LZ-H025GBA4


























Reviews:

No comments

Related manuals for LZ-H025GBA4

Brand: Data Aire Pages: 64

Brand: Data Aire Pages: 123

Brand: Klarstein Pages: 64

Brand: Samsung Pages: 30

Brand: Samsung Pages: 52

Brand: Samsung Pages: 58

Brand: Samsung Pages: 27

Brand: Samsung Pages: 26

Brand: Samsung Pages: 28

Brand: Samsung Pages: 28

Brand: Samsung Pages: 26

Brand: Samsung Pages: 17

AM072BXV Series

Brand: Samsung Pages: 326

Brand: Samsung Pages: 26

Brand: Samsung Pages: 1

Brand: Carrier Pages: 15

GWC09NA-D3NNA3A/I

Brand: Gree Pages: 72

Brand: Kelvinator Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands