LG Hydro Kit Installation Manual Download Page 41

Page: 41 / 77

Accessories Installation

Hydro Kit

Installation Manual

ENGLISH

How to Wire Thermostat

Follow below procedures Step 1 ~ Step 6.

Step 1.

Uncover front cover of the unit and open the control box.

Step 2.

Identify the power specification of the thermostat. If it is 230 V AC, go to Step 4. Otherwise, if
it is 24 V AC, go to step 3.

Step 3.

Find thermostat connecting cable A and C. Disconnect cable A and C, then connect cable B and C.

Step 4.

If it is Heating Only Thermostat, go to step 5. Otherwise, if it is Heating / Cooling Thermostat,
go to step 6.

Step 5.

Find terminal block and connect wire as below. After connecting, go to step 6.

WARNING

Mechanical type Thermostat.

Do not connect wire (N) as mechanical type thermostat does not
require electric power supply.

CAUTION

Do not connect external electric loads.

Wire (L) and (N) should be used only for operation Electric type
thermostat.
Never connect external electric loads such as valves, fan coil units, etc.
If connected, Main PCB Assembly 1 can be seriously damaged.

Thermostat

(L)

(N)

(H)

THERMOSTAT

(Default : 230 V AC)

1
L

Second:
Connect
B and C

First:
Disconnect
A and C

(L) : Live signal from PCB to Thermostat
(N) : Neutral signal from PCB to Thermostat
(H) : Heating signal from Thermostat to PCB

Summary of Contents for Hydro Kit














































































Search results

Summary of Contents for Hydro Kit

Reviews:

Related manuals for Hydro Kit

Brands by name

Popular brands

LG Hydro Kit, Installation Manual

Search results

Summary of Contents for Hydro Kit

Reviews:

Related manuals for Hydro Kit

Brands by name

Popular brands