LG GB175 Service Manual Download Page 20

Page: 20 / 158

-20-

Noise Reduction

Echo Suppression / Echo Cancellation

Advanced Sidetone Oscillation Reduction

Digital sidetone generator with programmable gain

Two programmable acoustic compensation filters

GSM/GPRS quad vocoders for adaptive multirate (AMR), enhanced full rate (EFR), full rate

(FR) and half rate (HR)

FR error concealment

GSM channel coding, equalization and A5/1, A5/2 and A5/3 ciphering

GPRS GEA1, GEA2 and GEA3 ciphering

Programmable GSM/GPRS Modem

Packet Switched Data with CS1/CS2/CS3/CS4 coding schemes

GSM Circuit Switch Data

GPRS Class 12

Voice Interface and Voice Front End

Two microphone inputs sharing one low noise amplifier with programmable gain and automatic

gain control (AGC) mechanism

Voice power amplifier with programmable gain

2nd order Sigma-Delta A/D Converter for voice uplink path

D/A Converter for voice downlink path

Supports half-duplex hands-free operation

Compliant with GSM 03.50

3.1.4 Multi-Media Features

LCD/NAND Flash Interface

18-bit Parallel Interface supports 8/16 bit NAND flash and 8/9/16/18 bit Parallel LCD

8/16 bit NAND Flash Controller with 1-bit ECC correction for mass storages

2 Chip selects available for high-density NAND flash device

Serial LCD Interface with 8/9 bit format support

LCD Controller

Hardware accelerated display

Supports simultaneous connection to up to 2 parallel LCD and 1 serial LCD modules

Supports format: RGB332, RGB444, RGB565, RGB666, RGB888

Supports LCD panel maximum resolution up to 800x600 at 16bpp

Supports hardware display rotation

Capable of combining display memories with up to 4 blending layers

Accelerated Gamma correction with programmable gamma table.

Image Signal Processor

8 bit YUV format image input

Capable of processing image of size up to VGA

Flexible I/O voltage of 1.8V ~ 2.8V

Audio CODEC

Wavetable synthesis with up to 64 tones

Advanced stereo wavetable synthesizer

Wavetable including GM full set of 128 instruments and 47 sets of percussions

PCM Playback and Record

Digital Audio Playback

HE-AAC decode support

Audio Interface and Audio Front End

Supports I2S interface

Summary of Contents for GB175































































































































































Search results

Summary of Contents for GB175

Reviews:

LG GB175, Service Manual, Page: 20 / 158

Search results

Summary of Contents for GB175

Reviews: