LG CM2460 Service Manual Download Page 32 | Manualshive

Page: 32 / 60

background image

3-15

ONE POINT REPAIR GUIDE

NO SOUND

There is no sound output in the TUNER FUNCTION, repair the set according to the following guide.

5-5. IN THE TUNER FUNCTION

5-5-1. Solution

Please check and replace IC400, IC402 on MAIN board.

5-5-2. How to troubleshoot (Countermeasure)

1) Check if TUL_L/R is entered from pin13, 14 of IC402 to IC403 pin1, 12.



If no signals, check +3.3 V for tuner power.



Check if the TUNER control signals (TUN_RST, TUN_SDA AND TUN_SCL) are entered from IC105 to IC402

If it doesn’t work, replace TUNER with a new one.
2) Check if MCS_TX_BCK, MCS_RX_MCLK and MCS_TX_LRCK are entered from IC105 to IC400.
3) Check if MCS_RX_ADATA is entered from IC400 to IC105.



If no signal, check +3.3 V (ADC) for IC400. If is NG, replace it with a new one.

4) Check the following I2S audio signal flow from IC105 to IC700. (Refer to Item 5-1.)



If there is any trouble, check the power for each IC. The power is normal but, if the signal waveform to

the IC is distorted or no signal, replace it with a new one.
5) Check if the digital audio AMP block is okay. Refer to “Digital Audio AMP” guide on Item 5-2.



If AMP is damaged, replace it with a new one.

5-5-3. Service hint (Any picture/ Remark)

PWM

PS9

860

TAS5612L

FR,FL

Z

H

M

6

7

5

.

4

2

DSP IC105

MLC3730S

176PIN BGA

IC403 CD4052

TUNER

TU_L/R

Interrupt

controller

CDROM x8 speed

Decoder

NAND Controller

within BCH codec

14bits ECC

GDMA 3ch

ADC (12bit*5ch)

Timer, Watchdog

GPIO (72 Max)

SPI 4ch (Max)

RTC & Wake up

UART 4ch (Max)

I2C 2ch

SDHC-SDIO 4ch (Max)

USB 2.0 OTG

SRAM (10K)

Main Processor

Audio DSP-0

GDMA 2ch

USB 1.1

Host/Device

ARM

926EJS

16KB

I-Cache

16KB

D-Cache

400Mhz

DSP

133Mhz

SRAM29KB

I-Cache 8KB

D-Cache 8KB

Boot ROM (20KB)

SDRAM

Controller

IC401 CD4558

IC400 CJC5357

IC700

IC402 Si4702

< Signal check point >

< TUNER IN function signal

fl

ow >

TUN_L to C435

TUN_L to C435

TUN_R to C434

TUN_R to C434

IC402

IC402

«
...
30
31
32
33
34
...
»

Summary of Contents for CM2460





























































Reviews:

No comments

Related manuals for CM2460

AM2 - SCHEMATICS

Brand: Martin Audio Pages: 1

Brand: Xblitz Pages: 40

Brand: B&W electronics Pages: 33

Brand: Yamaha Pages: 24

Brand: Dali Pages: 8

Brand: Dali Pages: 42

Brand: Dali Pages: 34

Brand: Dali Pages: 2

Brand: Dali Pages: 37

Brand: Dali Pages: 2

Brand: Dali Pages: 15

Brand: GAIT Pages: 2

Brand: akira Pages: 15

Brand: Vonyx Pages: 16

Brand: JLab Audio Pages: 2

Brand: QSC Pages: 4

Black Pearl V.2

Brand: Audio Pro Pages: 1

Brand: Keas Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands