LG CM2460 Service Manual Download Page 10

Page: 10 / 60

SPECIFICATIONS

1-9

• GENERAL

Power requirements

Refer to the main label.

Power consumption

Refer to the main label.

Networked standby : 0.5 W (If all network ports are activated.)

Dimensions (W x H x D)

Approx. 230 mm x 125 mm x 236 mm

Net Weight

Approx. 2.1 kg

Operating temperature

5 °C to 35 °C

Operating humidity

5 % to 90 %

• INPUTS

Portable in (PORT. IN)

0.4 Vrms (3.5 mm stereo jack) x 1

• TUNER

FM Tuning Range

87.5 to 108.0 MHz or 87.50 to 108.00 MHz

• AMPLIFIER (RMS OUTPUT POWER)

Total

100 W

Front

50 W (6

at 1 kHz, 10 % THD)

• SYSTEM

Frequency response

80 to 20,000 Hz

Signal-to-noise ratio

80 dB

Dynamic range

75 dB

Bus Power Supply (USB)

5 V 500 mA

•

FRONT SPEAKERS

Type

2 Way 2 Speaker

Impedance

Rated Input Power

50 W

Max. Input Power

100 W

Dimensions (W x H x D)

Approx. 150 mm x 250 mm x 140 mm

Net Weight

Approx. 1.52 kg

• Design and specifications are subject to change without notice.

Summary of Contents for CM2460





























































Search results

Summary of Contents for CM2460

Reviews:

Related manuals for CM2460

Brands by name

Popular brands

LG CM2460, Service Manual

Search results

Summary of Contents for CM2460

Reviews:

Related manuals for CM2460

Brands by name

Popular brands