LG ARNU053TRC4 Instruction Manual Download Page 48

Page: 48 / 58

Multi V Ceiling Cassette Indoor Unit

Due to our policy of continuous product innovation, some specifications may change without notification.

INSTALL DECORATION PANEL

2-Way Cassette

Figure 32: Decoration Panel Installation

2-Way Decoration Panel Installation

1. Install two decoration panel attaching screws on the cassette chassis. Tighten about

3/8 inch.

2. Remove the air inlet grille from the decoration panel. (Remove the hook for the air

inlet grille cord.)

3. Hook the decoration panel key hole on the screws in-

stalled, and slide the panel so that the screws

reach the key hole edge.

4. Tighten completely the two initially installed

screws and two additional screws.

5. Connect the louver motor connector and

display connector.

6. After tightening these screws, install the air

inlet grille (including the air filter)

Piping side

Decorative panel

Push

Control box cover

Cover

Filter

Key holes

Decorative panel

attaching screws

Louver motor

Ratch pull

Inlet Grille

Safety grille

Attaching screws

Summary of Contents for ARNU053TRC4



























































Search results

Summary of Contents for ARNU053TRC4

Reviews:

Related manuals for ARNU053TRC4

Brands by name

Popular brands

LG ARNU053TRC4, Instruction Manual

Search results

Summary of Contents for ARNU053TRC4

Reviews:

Related manuals for ARNU053TRC4

Brands by name

Popular brands