manualshive.com logo in svg

LG ARNU053TRC4, Instruction Manual

Share
Download
LG ARNU053TRC4 Instruction Manual Download Page 47

47

Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

Cassette chassis

Decoration panel

Control box cover

Piping side

Louver motor

Control panel

Lead wire for

louver motor

and control panel

Decoration panel

attaching screws 

Decoration panel

attaching screws 

Decoration panel

removeable corners 

Inlet

Grill

Cassette

chassis

Ceiling board

Decoration panel

Air

Cool air leaking

through gap

Cassette chassis against

decoration panel with no gap

Air

Cassette

chassis

No air gap

Ceiling board

Correct Installation

Incorrect Installation

Figure 29: Decoration Panel Installation

Figure 30: Swing Inlet Grill Downward

Figure 31: Properly Seating Decoration Panel against Chassis

INSTALL DECORATION PANEL

Decoration Panel Installation

1.  Install two decoration panel attaching screws on the cassette chassis. Tighten about 3/8 inch.
2.  Remove the air inlet grille from the decoration panel. (Remove the hook for the air inlet grille cord.)
3.  Hook the decoration panel key hole on the screws installed, and slide the panel so that the screws reach the key hole edge.
4.  Tighten completely the two initially installed screws and two additional screws.
5.  Connect the louver motor connector and display connector.
6.  After tightening these screws, install the air inlet grille (including the air filter).

4-Way Cassette

Summary of Contents for ARNU053TRC4



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands