LG AHNW166T0 Installation Manual Download Page 6

Page: 6 / 73

Safety Precautions

If the unit is not used for long time, we strongly recommend not to switch off
the power supply to the unit.

• There is risk of water freezing.

When the unit is
soaked (flooded or sub-
merged), contact an
Authorized Service
Center.

• There is risk of fire or

electric shock.

Be cautious that water
could not be poured to
the unit directly.

• There is risk of fire, elec-

tric shock, or unit dam-
age.

Ventilate the unit from
time to time when oper-
ating it together with a
stove, etc.

• There is risk of fire or

electric shock.

Turn the main power off
when cleaning or main-
taining the unit.

• There is risk of electric

shock.

Take care to ensure
that nobody could step
on or fall onto the unit.

• This could result in per-

sonal injury and unit
damage.

For installation, always
contact the dealer or an
Authorized Service
Center.

• There is risk of fire, elec-

tric shock, explosion, or
injury.

Summary of Contents for AHNW166T0










































































Search results

Summary of Contents for AHNW166T0

Reviews:

Related manuals for AHNW166T0

Brands by name

Popular brands

LG AHNW166T0, Installation Manual

Search results

Summary of Contents for AHNW166T0

Reviews:

Related manuals for AHNW166T0

Brands by name

Popular brands