LG A5UW40GFA1 Installation Manual Download

Page: 34 / 39

FUNCTION

ENGLISH

• If comp frequency and fan speed are down, the cooling capacity may decrease accordingly.

• This function is only available for Cooling Mode.

• If you want to stop the Night Quiet Mode, Change the DIP Switch.

• If operating indoor unit is set by the fan speed “Power”, Night Quiet Mode will be stopped

until fan speed “Power” is changed.

CAUTION

Mode Lock

Setting Procedure

Set the DIP Switch as follow after shutting the power source down.

Reset the power.

Mode Lock with Night Quiet Mode

Saving Power Consumption with Mode Lock.

Mode Lock (Cooling)

+ Night Quiet Mode

(step 1)

Mode Lock (Cooling)

+ Night Quiet Mode

(step 2)

Mode Lock (Cooling)

+ Saving Power

Consumption (step 1)

Mode Lock (Heating)

+ Saving Power

Consumption (step 1)

Mode Lock (Cooling)

+ Saving Power

Consumption (step 2)

Mode Lock (Heating)

+ Saving Power

Consumption (step 2)

Only Cooling Mode

Only Heating Mode

Summary of Contents for A5UW40GFA1








































Search results

Summary of Contents for A5UW40GFA1

Reviews:

Related manuals for A5UW40GFA1

Brands by name

Popular brands

LG A5UW40GFA1, Installation Manual

Search results

Summary of Contents for A5UW40GFA1

Reviews:

Related manuals for A5UW40GFA1

Brands by name

Popular brands