LG A5UW40GFA1 Installation Manual Download

Page: 37 / 39

SEASONAL WIND AND CAUTIONS IN WINTER

ENGLISH

SEASONAL WIND AND CAUTIONS IN WINTER

- Sufficient measures are required in a snow area or severe cold area in winter so that product

can be operated well.

- Get ready for seasonal wind or snow in winter even in other areas.

- Install a suction and discharge duct not to let in snow or rain.

- Install the outdoor unit not to come in contact with snow directly. If snow piles up and freezes

on the air suction hole, the system may malfunction. If it is installed at snowy area, attach the

hood to the system.

- Install the outdoor unit at the higher installation console by 50 cm than the average snowfall

(annual average snowfall) if it is installed at the area with much snowfall.

- Where snow accumulated on the upper part of the Outdoor Unit by more than 10 cm, always

remove snow for operation.

The height of H frame must be more than 2 times the snowfall and its width shall not
exceed the width of the product. (If width of the frame is wider than that of the product,
snow may accumulate)

Don't install the suction hole and discharge hole of the Outdoor Unit facing the seasonal
wind.

Model

Current(A)

A2UW16GFA0

8.4

A3UW21GFA0

11.0

A5UW30GFA0

16.5

A5UW40GFA1

29.0

A5UW48GFA1

A7UW40GFA0

26.0

A8UW48GFA0

27.0

A9UW56GFA0

Frequency / Voltage

• Argentina : 50 Hz 220-240 V~

• Mexico, Brazil : 60 Hz 220 V~

Summary of Contents for A5UW40GFA1








































Search results

Summary of Contents for A5UW40GFA1

Reviews:

Related manuals for A5UW40GFA1

Brands by name

Popular brands

LG A5UW40GFA1, Installation Manual

Search results

Summary of Contents for A5UW40GFA1

Reviews:

Related manuals for A5UW40GFA1

Brands by name

Popular brands