LG 55SM5KD-B User Manual Download Page 29

Page: 29 / 75

English

Audio Out

Sound Audio Out

•

Off

: Disables the use of

Audio Out

. (No audio outputted.)

•

Variable

: You can specify an output range for the external audio device connected to the monitor and adjust the

volume within the range. You can change the volume of an external audio device within the range of 0 to

100 (the same as the Signage speaker volume). However, there may be a difference in the actual volume

level outputted.

•

Fixed

: Set a fixed audio output level for the external audio device.

- If there is no external input, no external audio is outputted.

- The variable audio output level 100 is the same as the fixed audio output level.

Volume Increase Amount

Sound Volume Increase Amount

This feature enables you to adjust the amount of volume that increases/decreases when you press the up/down volume

key on your remote control. The higher the value you set, the faster the volume increases. Choose from among

Low

Medium

, and

High

to adjust the volume range.

AV Sync. Adjustment

Sound AV Sync. Adjustment

This feature adjusts audio timing to synchronize video and audio.

•

External Speaker

: Adjust the sync between video and audio coming from external speakers, such as those connected

to the digital audio output port, LG audio equipment, or headphones. Moving closer to – speeds up

the audio output, while moving closer to + slows down the audio output, compared to the default

value.

•

Bypass

: Output the broadcast signals or the sound from external devices without any audio delay. Audio may be

outputted earlier than video due to the processing time for video that is inputted into the monitor.

Digital Audio Input

Sound Digital Audio Input

This feature enables you to choose an input source for audio output.

•

Digital

: Output the audio contained in the digital signal inputted from the connected digital input source (HDMI,

DISPLAYPORT, or OPS).

•

Analog

: Output audio from the digital input source (HDMI, DISPLAYPORT, or OPS) connected to the monitor through

the Audio In port.

Summary of Contents for 55SM5KD-B












































































Search results

Summary of Contents for 55SM5KD-B

Reviews:

Related manuals for 55SM5KD-B

Brands by name

Popular brands

LG 55SM5KD-B, User Manual

Search results

Summary of Contents for 55SM5KD-B

Reviews:

Related manuals for 55SM5KD-B

Brands by name

Popular brands