LFA RTP 9 User Manual Download Page 83

Page: 83 / 95

Fill Tray Thumb Bolts

The Fill Tray Thumb Bolts secure the Fill
Tray onto the Turret. Order at

https://www.

lfatabletpresses.com/rtp-9-feeder-tray-thumb-
bolts

Fill Tray Scraper and Take-Off Blade

The Fill Tray Scraper (nonmetal) helps keep the
powder flowing into the Dies' bores, and the
Take-Off Blade (metal) aids in tablet ejection.
Order at

https://www.lfatabletpresses.com/rtp-9-

feeder-tray-scrapers

https://www.lfatabletpresses.com/take-off-

blade-rtp-9

V Belts

The V Belts connect to the Gearbox and the
Motor through the Drive Belt Pulleys. They aid
in intitiating the machine's operation. Order at

https://www.lfatabletpresses.com/rtp-9-drive-
belts

Lower Tracking

The Lower Tracking consists of three
components: the Ejection Cam, the Fill Cam,
and the Dosing Cam. These all guide and move
the Lower Punches. Order at

https://www.

lfatabletpresses.com/lower-tracking-kit-rtp-9

Dosing Cam Assembly Cog

Whenever the Fill Depth Knob is turned, the
weight of the tablets is increased or decreased.
Order at

https://www.lfatabletpresses.com/rtp-9-

lower-filling-adjustment-cog

Lower Roller Cam

The Lower Roller Cam guides the Lower Punches
to move along the Upper Tracking. It is also used
to adjust the pressure on the Lower Punches.
Order at

https://www.lfatabletpresses.com/rtp-9-

fill-cam

Summary of Contents for RTP 9
































































































Search results

Summary of Contents for RTP 9

Reviews:

Related manuals for RTP 9

Brands by name

Popular brands

LFA RTP 9, User Manual

Search results

Summary of Contents for RTP 9

Reviews:

Related manuals for RTP 9

Brands by name

Popular brands