Lexmark XM5163 Repair Manual Download Page 42

Page: 42 / 510

Retuning the ADF magnification

Note:

If the bottom arrows are touching the edge of the paper on both the front and the back side, the ADF scan

magnification is good and you can skip this section.

Power on the unit and perform an ADF Magnification test.

Navigate to Diagnostic mode

Scanner Tests

ADF Magnification

Review both of the saved ADF copies and see where the target arrows fall on the bottom of the page.

If you cannot see them you will need to

decrease

ADF Magnification until the arrows are touching the bottom of

the page. If you can see the arrows but they are not touching the bottom of the page, you will need to

increase

ADF magnification.

The range of adjustment is from

1.020

0.980

in increments of

0.005

7463

Repair information

412

Summary of Contents for XM5163































































































































































































































































































































































































































































































































Search results

Summary of Contents for XM5163

Reviews:

Brands by name

Popular brands

Lexmark XM5163, Repair Manual

Search results

Summary of Contents for XM5163

Reviews:

Brands by name

Popular brands