manualshive.com logo in svg

Lexmark XM5163, Repair Manual

Share
Download
Lexmark XM5163 Repair Manual Download Page 132

16

Remove the control panel board.

Control panel board and display removal (MX81x)

Control panel board removal (MX81x)

Warning—Potential Damage: 

When replacing the control panel, control panel board, or controller board, replace

only one component at a time. Replace the required component and perform a POR before replacing a second
component. If this procedure is not followed, the printer will be rendered inoperable. Never replace both the control
panel and the controller board without a POR after installing each one or the printer will be rendered inoperable.
Never install or remove these components as a method of troubleshooting while operating in normal user mode.
See 

“Controller board/control panel replacement” on page 372

.

Warning—Potential Damage: 

When a component has been installed in a machine and has been powered up in

normal user mode, it cannot be used in another machine; it must be returned to the manufacturer. The machine
must be powered up in Diagnostic mode or the controller board, control panel boards, or control panel will become
locked.

1

Remove the controller board access cover. See 

“Controller board access cover removal” on page 423

.

2

Remove the rear door. See 

“Rear door removal” on page 549

.

3

Remove the left cover. See 

“Left cover removal (MX81x)” on page 418

.

4

Open the front door.

5

Open the cartridge door.

6

Remove the column left front cover. See 

“Column left front cover removal (MX81x)” on page 414

.

7

Remove the left scanner cover. See 

“Flatbed scanner left cover removal topic” on page 633

.

7463

Repair information

502

Summary of Contents for XM5163































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands