4-206
Service Manual
7541-03x
Adjusting ADF magnification
1.
Enter the Diagnostic menu: press and hold
3
and
6
, turn on the printer, and release the buttons when the
splash screen appears.
2.
To print a test page from the Diagnostic menu, navigate to:
REGISTRATION
>
Quick Test
3.
To copy the test page from the Diagnostic menu, navigate to:
SCANNER CALIBRATION
>
Copy Quick Test
.
4.
Navigate to:
SCANNER TESTS
>
ADF Magnification
.
5.
Compare the copy to the original test page, and then adjust the value of the ADF Magnification setting as
needed. If the bottom margin is too small, decrease the value. If the bottom margin is too large, increase
the value.
6.
Touch
Submit
to save your changes.
7.
To check the changes, reload the original test page, and then repeat the Copy Quick Test. Repeat the
steps as needed.
8.
Once the margins look correct, check the registration of the ADF.
Perform the Copy Quick Test, and then repeat the process if needed.
Adjusting scanner registration
Note:
If the printer menus do not match the following instructions, then contact your next level of support.
1.
Enter the Configuration menu: press and hold
2
and
6
, turn on the printer, and release the buttons when
the splash screen appears.
2.
Navigate to:
Scanner Manual Registration
>
Print Quick Test
3.
Adjust the flatbed:
a.
Place the printed test page facedown on the flatbed scanner glass, and select
Copy Quick Test
.
b.
Compare the copy to the original test page.
c.
Select
Flatbed
, and adjust the left and top margins as needed.
d.
Touch
Submit
to save your changes.
e.
To check the changes, reload the original test page, and then repeat the Copy Quick Test. Repeat
the steps as needed.
4.
Adjust the ADF Front:
a.
Place the latest test page face up in the ADF, and select
Copy Quick Test
.
b.
Compare the copy to the original test page.
c.
Select
ADF Front
, and adjust the horizontal adjust and top margins as needed.
d.
Touch
Submit
to save your changes.
e.
To check the changes, reload the original test page, and then repeat the Copy Quick Test. Repeat
the steps as needed.
5.
Adjust the ADF Back:
a.
Place the latest test page facedown in the ADF, and select
Copy Quick Test
.
b.
Compare the copy to the original test page.
c.
Select
ADF Back
, and adjust the horizontal adjust and top margins as needed.
d.
Touch
Submit
to save your changes.
e.
To check the changes, reload the original test page, and then repeat the Copy Quick Test. Repeat
the steps as needed.
Touch
Back
to return to the Configuration Menu.
Summary of Contents for X925
