Diagnostic aids
3-7
7526
Go Back
Previous
Next
Print registration
To set print registration:
1.
Touch
REGISTRATION
from the Diag Menu.
2.
Touch
Quick Test
.
The message
Quick Test Printing…
appears on the display.
Note:
Retain this page to determine the changes you need to make to the margin settings.
3.
Touch the green arrow next to the margin setting you need to change.
4.
Use
to decrease or to increase the offset values, and then touch
Submit
.
The message
Submitting selection
displays, and then the original Registration screen appears with
the
beside the previously selected margin setting.
The print registration range is:
5.
Touch
Submit
to enter the values.
6.
Print the Quick Test to verify your changes
7.
Continue changing the settings by repeating steps 2 through 4.
Description
Value
Direction of change
Skew
-50 to +50 Each increment
corresponds to 1/1200 of an inch.
The skew setting value should be
between -5 and +5. If not, readjust
the skew with the printhead
mechanical setting. See
Top margin
-25 to +25 Each increment
corresponds to 8 scans at a 600 dpi
scan rate (0.0133 inches or
0.339 mm)
.
A positive change moves the image
down the page and increases the
top margin. A negative change
moves the image up and decreases
the top margin.
Bottom margin
-25 to +25 Each increment causes
approximately 0.55 mm shift in the
bottom margin.
A positive offset moves text up the
page and widens the bottom
margin. A negative offset moves
text down the page and narrows the
bottom margin.
Note:
Make sure the media size
selected matches the media size in
tray 1.
Left margin
-50 to +50 Each increment
corresponds to 4 pels at 600 dpi
(0.00666 in. or 0.1693 mm).
A positive change moves the image
to the right. A negative change
moves the image to the left. The
image is compressed or expanded.
Note:
Make sure the media size
selected matches the media size in
tray 1.
Right margin
-50 to +50 Each increment
corresponds to an approximate shift
of 4 pels at 600 dpi.
A positive change moves the image
to the right. A negative change
moves the image to the left.
Summary of Contents for X734DE
