Diagnostic aids
3-41
7526
Go Back
Previous
Next
Enforce Color Order
This setting gives the system support person the ability to enforce where the color cartridges may be placed,
and if messages appear when cartridges are in the wrong location.
When
On
(default) is selected, the printer lets users place each toner cartridge in only its specified slot. For
instance, the Magenta toner cartridge must be in the Magenta slot. If the user tries to place a cartridge in an
incorrect slot, the printer message
31 Defective or Missing <
color
> Cartridge
or
32 Unsupported <
color
>
Cartridge
appears where <
color
> stands for Cyan, Magenta, Yellow, or Black.
When
Off
is selected, the printer does not issue any message to let the user know that the cartridge is placed in
the wrong slot inside the printer.
To adjust the Enforce Color Order setting:
1.
Touch
Enforce Color Order
in the Config Menu.
2.
Touch the left arrow or the right arrow toggle between
Off
and
On
(default).
3.
Touch
Submit
.
Submitting changes…
is displayed.
You are automatically returned to the Configuration main menu.
Color Alignment
Color alignment should be performed when the transfer module is replaced.
To perform color alignment:
1.
Touch
Color Alignment
from the Config Menu.
2.
Touch
Print Alignment
.
Four pages print with charts and letters A–L.
3.
Consulting the printed page, look at Set A.
Indicate the number of the 20 color lines closest to the black lines.
4.
Enter that number on the operator panel using the left and right arrows.
5.
Continue selecting the best lines for the sets through
Set L and entering them on the operator panel
.
6.
Touch
Submit
when all are entered.
Color Adj State
These settings allow you to select when color calibrations occur. Selecting
Busy
indicates the color calibrations
will complete queued jobs, but refuse to add new jobs to the queue. When calibration is complete jobs are again
accepted. Selecting
Idle
allows calibrations only when the printer is idle.
To adjust the Color Adj State setting:
1.
Touch
Color Adj State
in the Config Menu.
2.
Touch the left arrow or the right arrow toggle between
Busy
and
Idle
.
3.
Touch
Submit
.
Submitting changes…
is displayed.
You are automatically returned to the Configuration main menu.
Summary of Contents for X734DE
