Lexmark 4500-00 Series Service Manual Download

Page: 186 / 246

4-8

Service Manual

4500

Cooling fan removal

1. Open the front cover. See

“Front cover” on page 4-4

for more

information.

2. Remove the top cover. See

“Top cover” on page 4-4

for more

information.

3. Remove the left side cover. See

“Left side cover” on page 4-5

for more information.

4. Remove two cooling fan screws.

5. Remove the toner cartridge.

6. For the E220/E321/E323, remove the right side cover and the

controller board cover.

7. Tilt the printer carefully to the rear so it is resting on the ASF.

8. Remove the four bottom cover screws.

9. Disconnect the cooling fan cable from the engine card

(E320/E322) or controller board (E220/E321/E323).

10. Remove the cooling fan.

Summary of Contents for 4500-00 Series























































































































































































































































Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands

Lexmark 4500-00 Series, Service Manual

Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands