Lexmark 4500-00 Series Service Manual Download

Page: 126 / 246

2-96

Service Manual

4500

The paper sticks together/printer
feeds multiple sheets of paper.

• Remove the paper from Tray 1 or

the optional Tray 2 and fan the
paper.

• Don’t overfill Tray 1 or the optional

Tray 2 (see media capacities in
the media types and sizes chart in
the

User’s Reference

The paper fails to feed from
Tray 1.

• Remove the paper from Tray 1

and fan the paper.

• Make sure Tray 1 is selected from

the printer driver.

• Do not overfill the tray.
• Check the rubber on the D–roll

assembly (pick roll).

Problem

Action

Summary of Contents for 4500-00 Series























































































































































































































































Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands

Lexmark 4500-00 Series, Service Manual

Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands