Lexmark 4500-00 Series Service Manual Download

Page: 191 / 246

Repair information

4-13

4500

Printhead assembly removal

1. Open the front cover. See

“Front cover” on page 4-4

for more

information.

2. Remove the top cover. See

“Top cover” on page 4-4

for more

information.

3. Remove the four top screws from the printhead mounting plate.

4. Remove the printhead plate ground strap screw above the

HVPS.

5. Remove the controller cage screw from the printhead mounting

plate.

6. Disconnect the printhead cables (first at the controller card for

E220/E321/E323 only).

7. Remove the three printhead screws (E320/E322 only).

8. Remove the printhead.

Transfer roll removal

1. Open the front cover and remove the toner cartridge. See

“Front cover” on page 4-4

for more information.

2. Release the transfer roll left and right bearing.

3. Remove the transfer roll.

Summary of Contents for 4500-00 Series























































































































































































































































Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands

Lexmark 4500-00 Series, Service Manual

Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands