Lexmark 4500-00 Series Service Manual Download Page 182 | Manualshive

Page: 182 / 246

background image

4-4

Service Manual

4500

Removal procedures

Be sure to unplug the power cord whenever you are
working on the printer with one of the covers removed.
Be sure to remove the print cartridge before you
perform removal procedures.

Cover removals

Access cover

1. Open the front access cover.

2. Press the center of the access cover down to release the side

pivot points.

3. Remove the access cover.

Front cover

1. Open the front cover.

2. Remove the two plastic clips from the front cover support arm

hinges.

Note:

Support and ease the charge roll assembly into a resting

position when disengaging the front cover support arm
hinges.

3. Disengage the front cover support arm hinges from the charge

roll assembly.

4. Release the front cover from its pivot points.

Note:

Lay the front cover to one side as the operator panel

cable is attached to the controller card. See

“Right side

cover” on page 4-5

“Controller card cage

removal” on page 4-7

for more information.

Top cover

1. Open the front cover.

2. Remove the two top cover screws.

3. Remove the top cover.

«
...
180
181
182
183
184
...
»

Summary of Contents for 4500-00 Series























































































































































































































































Reviews:

No comments

Related manuals for 4500-00 Series

Brand: Datamax Pages: 2

Brand: Oki Pages: 2

OKIPAGE 8c Plus

Brand: Oki Pages: 48

Brand: Oki Pages: 257

Brand: Oki Pages: 113

Brand: Oki Pages: 26

Brand: Oki Pages: 183

Brand: Oki Pages: 36

Brand: Oki Pages: 136

Brand: Oki Pages: 66

Brand: Oki Pages: 123

Brand: Oki Pages: 109

Brand: Oki Pages: 68

Brand: Oki Pages: 12

Brand: Oki Pages: 22

Brand: Oki Pages: 22

Brand: Oki Pages: 27

OKIPAGE 12i Series

Brand: Oki Pages: 210

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands