LevelOne GTL-2881 User Manual Download Page 529 | Manualshive

Page: 529 / 706

background image

Chapter 14

| Multicast Filtering

Layer 2 IGMP (Snooping and Query for IPv4)

– 529 –

Note:

Multicast routers use this information from IGMP snooping and query

reports, along with a multicast routing protocol such as DVMRP or PIM, to support
IP multicasting across the Internet.

Parameters

These parameters are displayed:

◆

IGMP Snooping Status

– When enabled, the switch will monitor network

traffic to determine which hosts want to receive multicast traffic. This is referred
to as IGMP Snooping. (Default: Enabled)

When IGMP snooping is enabled globally, the per VLAN interface settings for
IGMP snooping take precedence (see

“Setting IGMP Snooping Status

per Interface” on page 537

When IGMP snooping is disabled globally, snooping can still be configured per
VLAN interface, but the interface settings will not take effect until snooping is
re-enabled globally.

◆

Proxy Reporting Status

– Enables IGMP Snooping with Proxy Reporting.

(Default: Disabled)

When proxy reporting is enabled with this command, the switch performs
“IGMP Snooping with Proxy Reporting” (as defined in DSL Forum TR-101, April
2006), including last leave, and query suppression.

Last leave sends out a proxy query when the last member leaves a multicast
group, and query suppression means that specific queries are not forwarded
from an upstream multicast router to hosts downstream from this device.

When proxy reporting is disabled, all IGMP reports received by the switch are
forwarded natively to the upstream multicast routers.

◆

TCN Flood

– Enables flooding of multicast traffic if a spanning tree topology

change notification (TCN) occurs. (Default: Disabled)

When a spanning tree topology change occurs, the multicast membership
information learned by switch may be out of date. For example, a host linked to
one port before the topology change (TC) may be moved to another port after
the change. To ensure that multicast data is delivered to all receivers, by
default, a switch in a VLAN (with IGMP snooping enabled) that receives a Bridge
Protocol Data Unit (BPDU) with TC bit set (by the root bridge) will enter into
“multicast flooding mode” for a period of time until the topology has stabilized
and the new locations of all multicast receivers are learned.

If a topology change notification (TCN) is received, and all the uplink ports are
subsequently deleted, a time out mechanism is used to delete all of the
currently learned multicast channels.

When a new uplink port starts up, the switch sends unsolicited reports for all
currently learned channels out the new uplink port.

«
...
527
528
529
530
531
...
»

Summary of Contents for GTL-2881



































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GTL-2881

Brand: D-Link Pages: 2

RackSwitch G8264

Brand: IBM Pages: 20

Flex System FC3171

Brand: IBM Pages: 64

Brand: CoolGear Pages: 2

Brand: IDEM SAFETY SWITCHES Pages: 2

FlowPoint 2100 12

Brand: Cabletron Systems Pages: 36

Brand: Hawking Pages: 2

Brand: Kramer Pages: 2

Brand: Quintech Pages: 2

Brand: N-Tron Pages: 16

Brand: Shinybow USA Pages: 16

Brand: Velleman Pages: 8

Brand: Microsonic Pages: 2

Brand: Ubiquiti Pages: 23

Brand: Exsys Pages: 2

Brand: Icy Box Pages: 10

Brand: Comm-Tec Pages: 40

Brand: Grizzly Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands