manualshive.com logo in svg

LevelOne GTL-2881, User Manual

The LevelOne GTL-2881 User Manual is readily available for free download from our website. This comprehensive manual provides detailed step-by-step instructions for setting up and operating the LevelOne GTL-2881 product. Access it now at manualshive.com to enhance your user experience with this exceptional product.

Share
Download
background image

Chapter 12

  |  Security Measures

DoS Protection

–  355  –

◆

Smurf Attack

 – Attacks in which a perpetrator generates a large amount of 

spoofed ICMP Echo Request traffic to the broadcast destination IP address 
(255.255.255.255), all of which uses a spoofed source address of the intended 
victim. The victim should crash due to the many interrupts required to send 
ICMP Echo response packets. (Default: Enabled)

◆

TCP Flooding Attack

 – Attacks in which a perpetrator sends a succession of 

TCP SYN requests (with or without a spoofed-Source IP) to a target and never 
returns ACK packets. These half-open connections will bind resources on the 
target, and no new connections can be made, resulting in a denial of service. 
(Default: Disabled)

◆

TCP Flooding Attack Rate

 – Maximum allowed rate. (Range: 64-2000 kbits/

second; Default: 1000 kbits/second)

◆

TCP Null Scan

 – A TCP NULL scan message is used to identify listening TCP 

ports. The scan uses a series of strangely configured TCP packets which contain 
a sequence number of 0 and no flags. If the target's TCP port is closed, the 
target replies with a TCP RST (reset) packet. If the target TCP port is open, it 
simply discards the TCP NULL scan. (Default: Enabled)

◆

TCP-SYN/FIN Scan

 – A TCP SYN/FIN scan message is used to identify listening 

TCP ports. The scan uses a series of strangely configured TCP packets which 
contain SYN (synchronize) and FIN (finish) flags. If the target's TCP port is 
closed, the target replies with a TCP RST (reset) packet. If the target TCP port is 
open, it simply discards the TCP SYN FIN scan. (Default: Enabled)

◆

TCP Xmas Scan

 – A so-called TCP XMAS scan message is used to identify 

listening TCP ports. This scan uses a series of strangely configured TCP packets 
which contain a sequence number of 0 and the URG, PSH and FIN flags. If the 
target's TCP port is closed, the target replies with a TCP RST packet. If the target 
TCP port is open, it simply discards the TCP XMAS scan. (Default: Enabled)

◆

TCP/UDP Packets with Port 0

 – Protects against DoS attacks in which the TCP 

or UDP source port or destination port is set to zero. This technique may be 
used as a form of DoS attack, or it may just indicate a problem with the source 
device. When this command is enabled, the switch will drop these packets. 
(Default: Enabled)

Note:

 Due to a chip limitation, this command does not work when the TCP source 

port/destiation port or UDP source port/destiation port are both set to zero.

◆

UDP Flooding Attack

 – Attacks in which a perpetrator sends a large number of 

UDP packets (with or without a spoofed-Source IP) to random ports on a 
remote host. The target will determine that application is listening at that port, 
and reply with an ICMP Destination Unreachable packet. It will be forced to 
send many ICMP packets, eventually leading it to be unreachable by other 
clients. (Default: Disabled)

Summary of Contents for GTL-2881



































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GTL-2881

D-Link DUB-H4 - Hub - USB Installation Manual preview
DUB-H4 - Hub - USB
Brand: D-Link Pages: 4
D-Link DSS-16+ Quick Install Manual preview
DSS-16+
Brand: D-Link Pages: 2
H3C s5800 series Configuration Manual preview
s5800 series
Brand: H3C Pages: 22
H3C S5500-EI series Quick Start preview
S5500-EI series
Brand: H3C Pages: 2
D-Link DES-3326SRM Product Manual preview
DES-3326SRM
Brand: D-Link Pages: 242
H3C S5170-EI Series Manual preview
S5170-EI Series
Brand: H3C Pages: 46
Contemporary Controls EISK5-100T/H Installation Manual preview
EISK5-100T/H
Brand: Contemporary Controls Pages: 4
Hama 00047693 Operating Instructions preview
00047693
Brand: Hama Pages: 2
N-Tron 100-POE4-MDR User Manual & Installation Manual preview
100-POE4-MDR
Brand: N-Tron Pages: 17
SUCO 0140 Series Operating Instructions preview
0140 Series
Brand: SUCO Pages: 2
S&C Omni-Rupter Series Installation And Operation Manual preview
Omni-Rupter Series
Brand: S&C Pages: 31
Lantech IES-5222T Series User Manual preview
IES-5222T Series
Brand: Lantech Pages: 30
TekTone Tek-CARE NC554/8 Installation Instructions preview
Tek-CARE NC554/8
Brand: TekTone Pages: 2
3onedata IES6300PRO Series Quick Installation Manual preview
IES6300PRO Series
Brand: 3onedata Pages: 5
DELTA DORE TYXIA 4600 Manual preview
TYXIA 4600
Brand: DELTA DORE Pages: 3
Foxun SX-EW70 Operating Instructions Manual preview
SX-EW70
Brand: Foxun Pages: 7
Gefen EXT-DPKVM-841 User Manual preview
EXT-DPKVM-841
Brand: Gefen Pages: 31
Yacoub Automation GmbH SM 4TX2FX User Manual preview
SM 4TX2FX
Brand: Yacoub Automation GmbH Pages: 45

Brands by name

Popular brands

Load more brands