Leuze BCL 8 Original Operating Instructions Download Page 35

Page: 35 / 63

Configuration and diagnostics software - Sensor Studio

Leuze electronic GmbH + Co. KG

BCL 8

Configuration and diagnostics software - Sensor Studio

The

Sensor Studio

configuration software provides a graphical user interface for operation, configuration

and diagnosis of the device via the RS 232 service interface.
A device that is not connected to the PC can be configured offline.
Configurations can be saved and reopened as projects for transferring back to the device at a later time.

The

Sensor Studio

configuration software is designed according to the FDT/DTM concept:

• You make the individual configuration settings for the bar code reader in the Device Type Manager

(DTM).

• The individual DTM configurations of a project can be called up via the frame application of the Field

Device Tool (FDT).

• Communication DTM for bar code readers:

LeCommInterface

• Device DTM for BCL 8 bar code reader

Procedure for the installation of the software and hardware:



Install the

Sensor Studio

configuration software on the PC. Install the communication and device DTM.



Communication and device DTMs are included in the

LeAnalysisCollectionSetup

installation package.



Create the device DTM for BCL 8 in the project tree of the

Sensor Studio

FDT frame.



Connect the bar code reader to the PC (see chapter "Connecting").



Activate service interface on bar code reader (see chapter "Activate service interface").

9.1

System requirements

To use the

Sensor Studio

configuration software, you need a PC or laptop with the following specifications:

Table 9.1:

System requirements for

Sensor Studio

installation

NOTE

Only use the

Sensor Studio

configuration software for products manufactured by Leuze.

The

Sensor Studio

configuration software is offered in the following languages: German,

English, French, Italian and Spanish.
The FDT frame application of

Sensor Studio

supports all languages; it is possible that not all

languages are supported in the device DTM (Device Type Manager).

Operating system

Windows XP or higher (32 bit, 64 bit)

Windows Vista

Windows 7

Windows 8

Computer

Processor type: 1 GHz or higher

Serial COM interface

CD-ROM drive

Main memory (RAM): at least 64 MB

Keyboard and mouse or touchpad

Graphics card

At least 1024 x 768 pixels

Required hard disk capacity for

Sen

sor Studio

and communication DTM

35 MB

NOTE

Administrator privileges on the PC are necessary for installing

Sensor Studio

Summary of Contents for BCL 8
































































Search results

Summary of Contents for BCL 8

Reviews:

Related manuals for BCL 8

Brands by name

Popular brands

Leuze BCL 8, Original Operating Instructions

Search results

Summary of Contents for BCL 8

Reviews:

Related manuals for BCL 8

Brands by name

Popular brands