Let's Go Aero HexCap Manual Download Page 7

ONE YEAR LIMITED WARRANTY

We warrant this Let’s Go Aero brand product during the time the original retail purchaser owns 

the product. This warranty terminates if a purchaser transfers the product to any other person.

Let’s Go Aero warrants this product to be free from defect in material and workmanship for 

one year (retain your sales receipt for your records). Any product or part thereof found to be 

defective within that period will be replaced without charge provided that: (1) the product was 

not misused; (2) no alterations or modifications were made; (3) its failure was not a result of 

normal wear expected in the use of the product; (4) the product or part is delivered, freight 

prepaid, to Let’s Go Aero.

 

Manufacturers only obligation shall be to replace such products or parts proved to be defective. 

A Return Merchandise Authorization (RMA) is required prior to return. Please contact Let’s Go 

Aero toll-free, at 877-464-2376 or 719-630-3800, or via email to [email protected] to 

get an RMA number.

No warranty is given for LGA products purchased outside of the United States and Canada.

To register your product, visit the Let’s Go Aero website at www.LetsGoAero.com

To learn more about our products and stay informed about useful options for transporting all kinds of 

gear with your carrier, be sure to visit our website: www.LetsGoAero.com

Patent and trademark protected.

Patent Numbers 6,609,725; 6,945,550; 8,079,613; D717718; 8,858,141; Patents Pending

Copyright© 2017, Lets Go Aero, Inc., All rights reserved.

Technical Support

For assistance with this product, please contact us:

Let’s Go Aero, Inc.

4474 Barnes Road

USA

Phone: 877-464-2376 or 719-630-3800

Email: [email protected]

ALWAYS 

BE SURE THE LATCHES ARE FULLY LOCKED

 AND SECURE BEFORE TRANSIT. FAILURE TO 

PROPERLY LOCK AND SECURE THE HEXCAP LATCHES MAY RESULT BODILY INJURY, DEATH, AND/OR 

PROPERTY DAMAGE. NEVER BEGIN TRANSIT WITH THE HEXCAP COVER LATCHES UNLOCKED

ALWAYS 

BE SURE ALL CONNECTIONS ARE SNUG

 AND FULLY SECURE BEFORE TRANSIT. FAILURE TO 

PROPERLY CONNECT AND SECURE ALL CONNECTIONS MAY RESULT BODILY INJURY, DEATH, AND/OR 

PROPERTY DAMAGE. 

WARNING

WARNING

Page 7 of 7

Summary of Contents for HexCap








Reviews: