Lenze E84AYCEC Communications Manual Download Page 57

Page: 57 / 90

Lenze · E84AYCEC communication module (POWERLINK) · EDS84AYCEC EN 4.0 - 02/2019

Diagnostics

Troubleshooting with module signalling

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

[9-2]

Diagnostics - network wiring

E94YCEP052

2. Diagnostics - network wiring

X251/252

green LED

blinking?

Check the cable
connection and the
cable.

Check EPL master,
see point 1.

Switch on the EPL
devices.
Go back to point 2.

Create EPL wiring.
Go back to point 1.

Is at least one

cable

plugged?

X251/252,

green LED on?

Is the

module

connected to

it switched

on?

Point 3

Check EPL

master.
BS on /

blinking?

yes

off

Check EPL wiring to
EPL master.



Note!

The

(

Bus State

) LED refers to the Lenze communication module E94AYCEP as mana-

ging node.
This status display applies analogously to the managing nodes of other manufacturers.

Summary of Contents for E84AYCEC



























































































Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands

Lenze E84AYCEC, Communications Manual

Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands