Lenze E84AYCEC Communications Manual Download Page 22

Page: 22 / 90

Installation

Mechanical installation

Lenze · E84AYCEC communication module (POWERLINK) · EDS84AYCEC EN 4.0 - 02/2019

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

5.1

Mechanical installation

The communication module can be plugged in or unplugged from the MCI slot when the inverter is

switched on. When the module is plugged in, it is detected automatically, and a function and versi-

on plausibility check is executed.

5.1.1

Mounting for standard devices of 0.25 kW and 0.37 kW

[5-1]

Mounting for standard devices of 0.25 kW and 0.37 kW

Mounting steps

1. Use a screwdriver to lever out the cover of the MCI slot of the standard device and remove it (1,

2).

2. Loosen the securing screw for the communication module at the standard device (3).
3. Insert the communication module into the MCI slot of the standard device (4).
4. Tighten the securing screw again (5).

E84YCPM002D

Summary of Contents for E84AYCEC



























































































Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands

Lenze E84AYCEC, Communications Manual

Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands