manualshive.com logo in svg

Lenovo ThinkStation 1095, User Manual, Page: 24 / 136

Share
Download
Lenovo ThinkStation 1095 User Manual Download Page 24

15

Front panel connector (for connecting LED

indicators and the power switch)

38

PCI Express x16 graphics card slot

16

Auxiliary LED connector

39

PCI card slot

17

Hard disk drive enablement module connector

40

PCI Express x16 graphics card slot

18

Front USB connector (for connecting USB ports

1 and 2 on the front bezel)

41

PCI Express x4 card slot (x16 mechanical)

19

Internal USB connector

42

Rear fan connector

20

24-pin power connector

43

Microprocessor 2 memory slot 1 (DIMM1)

21

12-pin power connector

44

PS/2 keyboard and mouse connector

22

Hard disk drive LED for LSI card

45

Microprocessor 2 memory slot 2 (DIMM2)

23

SATA port 3

46

Microprocessor 2 12 V power connector

Locating internal drives

Internal drives are devices that your computer uses to read and store data. You can add drives to your
computer to increase storage capacity and enable your computer to read other types of media. Internal
drives are installed in bays. In this manual, the bays are referred to as bay 1, bay 2, and so on.

When installing or replacing an internal drive, it is important to note the type and size of the drive that you
can install or replace in each bay and correctly connect the cables to the drive installed. Refer to the
appropriate section in “Installing or replacing hardware” on page 29 for instructions on how to install or
replace internal drives for your computer.

Figure 5 “Drive bay locations” on page 12 shows the locations of the drive bays.

Figure 5. Drive bay locations

1

Bay 1 - Optical drive bay (with an optical drive installed in some models)

2

Bay 2 - Hard disk drive bay or solid state drive bay

12

ThinkStation User Guide

Summary of Contents for ThinkStation 1095









































































































































Reviews:

No comments