Message
Solution
0177:
Bad
SVP
data,
stop
POST
task.
Checksum
of
the
supervisor
password
in
the
EEPROM
is
not
correct.
The
system
board
should
be
replaced.
Have
the
computer
serviced.
0182:
Bad
CRC2.
Enter
BIOS
Setup
and
load
Setup
defaults.
Checksum
of
the
CRC2
setting
in
the
EEPROM
is
not
correct.
Go
to
BIOS
Setup
Utility.
Press
F9
and
then
Enter
to
load
the
default
setting.
Press
F10
and
then
Enter
to
restart
the
system.
0185:
Bad
startup
sequence
settings.
Enter
BIOS
Setup
and
load
Setup
defaults.
Checksum
of
the
startup
sequence
setting
in
the
EEPROM
is
not
correct.
Go
to
BIOS
Setup
Utility.
Press
F9
and
then
Enter
to
load
the
default
setting.
Press
F10
and
then
Enter
to
restart
the
system.
0187:
EAIA
data
access
error
The
access
to
EEPROM
has
failed.
Have
the
computer
serviced.
0188:
Invalid
RFID
Serialization
Information
Area.
The
EEPROM
checksum
is
not
correct
(block
#
0
and
1).
The
system
board
should
be
replaced,
and
the
box
serial
number
needs
to
be
reinstalled.
Have
the
computer
serviced.
0189:
Invalid
RFID
configuration
information
area
The
EEPROM
checksum
is
not
correct
(block
#
4
and
5).
The
system
board
should
be
replaced,
and
the
UUID
needs
to
be
reinstalled.
Have
the
computer
serviced.
0190:
Critical
low-battery
error
The
computer
turned
off
because
the
battery
is
low.
Connect
the
ac
adapter
to
the
computer
and
charge
the
battery,
or
replace
the
battery
with
a
fully
charged
one.
0191:
System
Security
-
Invalid
remote
change
requested.
The
system
configuration
change
has
failed.
Confirm
the
operation
and
try
again.
To
clear
the
error,
enter
the
BIOS
Setup
Utility.
0192:
System
Security
-
Embedded
Security
hardware
tamper
detected.
The
Security
Chip
has
been
replaced
with
a
different
one.
Have
the
computer
serviced.
0199:
System
Security
-
Security
password
retry
count
exceeded.
This
message
is
displayed
if
you
enter
a
wrong
supervisor
password
more
than
three
times.
Confirm
the
supervisor
password
and
try
again.
To
clear
the
error,
enter
the
BIOS
Setup
Utility.
01C8:
More
than
one
modem
devices
are
found.
Remove
one
of
them.
Press
<Esc>
to
continue.
Remove
a
Modem
Card.
Otherwise,
press
Esc
to
ignore
the
warning
message.
If
it
does
not
solve
this
problem,
have
the
computer
serviced.
01C9:
More
than
one
Ethernet
devices
are
found.
Remove
one
of
them.
Press
<Esc>
to
continue.
Your
ThinkPad
computer
has
a
built-in
Ethernet
feature,
and
you
cannot
add
another
such
feature
by
installing
an
Ethernet
device.
If
this
error
message
is
displayed,
remove
the
Ethernet
device
that
you
installed.
Otherwise
press
Esc
to
ignore
the
warning
message.
If
this
does
not
solve
the
problem,
have
the
computer
serviced.
Solving
computer
problems
Chapter
3.
Solving
computer
problems
11
Summary of Contents for ThinkPad T60 Series
