Lenovo DM120S Installation And Cabling Manual Download Page 20

Page: 20 / 70

Paths:

Controller

Initiator Initiator Side Switch Port Target Side Switch Port Target Port TPGN

------------ --------- ---------------------- ---------------------------- ----------- ------
stor-8080-1 1a

stor-8080-1 0d

stor-8080-2 1a

stor-8080-2 0d

Errors:
------
-

Step 5. If you disabled disk ownership automatic assignment in Step 1, manually assign disk ownership,

and then reenable disk ownership automatic assignment if needed:

a. Display all unowned disks:

storage disk show -container-type unassigned

b. Assign each disk:

storage disk assign -disk

disk_name

-owner

owner_name

You can use the wildcard character to assign more than one disk at once.

c. Reenable disk ownership automatic assignment if needed:

storage disk option modify -node

node_name

-autoassign on

You need to reenable disk ownership automatic assignment on both controllers in an HA pair.

Step 6. If your configuration is running in-band ACP, verify that in-band ACP was automatically enabled on

hot-added disk shelves:

storage shelf acp show

In the output, “in-band” is listed as “active” for each node.

Installation and Cabling Guide for DM120S, DM240S, and DM600S

Summary of Contents for DM120S







































































Search results

Summary of Contents for DM120S

Reviews:

Lenovo DM120S, Installation And Cabling Manual, Page: 20 / 70

Search results

Summary of Contents for DM120S

Reviews: