manualshive.com logo in svg

Lenovo DM120S, Installation And Cabling Manual, Page: 12 / 70

Share
Download
Lenovo DM120S Installation And Cabling Manual Download Page 12

If... 

Then... 

cabling is correct, a root aggregate is present, 
and run system-level diagnostics to identify 
any faulty components.

h. Complete system setup and configuration as 
instructed by the “Installation and Setup 
Instructions” that came with your system.

Step 6. 

If as part of system set up and configuration, you did not enable disk ownership automatic 

assignment, manually assign disk ownership; otherwise, go to the next step: 

a.  Display all unowned disks:  

storage disk show -container-type unassigned 

b.  Assign each disk:  

storage disk assign -disk 

disk_name 

-owner 

owner_name 

\ 

You can use the wildcard character to assign more than one disk at once.

Step 7.  Verify that in-band ACP was automatically enabled.  

storage shelf acp show  

In the output, “in-band” is listed as “active” for each node.

8

Installation and Cabling Guide for DM120S, DM240S, and DM600S

Summary of Contents for DM120S







































































Reviews:

No comments