manualshive.com logo in svg

Lennox Hearth Products RHAP42N, Installation Instructions Manual

Share
Download
Lennox Hearth Products RHAP42N Installation Instructions Manual Download Page 29

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

29

LENNOX HEARTH PRODUCTS  •  RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N)  •  INSTALLATION INSTRUCTIONS

INSTALLINg fIREPLACE COMPONENTS

(CONTINUEd)

INSTALLATION Of OPTIONAL  

SURROUNd

Surround installs after wall finish is complete. 

See 

Pages 32 and 33

.

Installation of Optional Bezel

1.  Hook  the  bezel  upper  flange  to  the  top 

edge  of  the  glass  door  frame,  and  then 

swing the lower edge of the bezel toward 

the door 

(Figure 51)

.

2.  Gently push the lower edge of the bezel to 

attach the bezel lower flange to the lower 

edge of the glass door frame.

Reverse these steps to remove the bezel.

Figure 51

Figure 50

Bezel Upper 

flange

Bezel Lower  

flange

[CROSS-SECTION]

glass door

frame

INSTALL MOdESTy PANEL

NOTE: Modesty panel will not be used if surround and bezel will be installed.

To install the modesty panel, insert the four hooks on modesty panel into the four slots on door 

flange, then slide panel to the LEFT until fully seated 

(see 

Figure 50

)

.

Modesty Panel

Insert hooks into slots 

(4 places), then slide 

panel left until seated

Hook on 

Modesty Panel

Slot on door 

flange

Summary of Contents for RHAP42N











































Reviews:

No comments

Brands by name

Popular brands

Load more brands