NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
24
Figure 43: Proflame Electronic Wiring Diagram
LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N) • INSTALLATION INSTRUCTIONS
Figure 42: Junction Box Wiring
green
ground
Screw
Red
Black
Hot
Side of
Receptacle
Tab Intact
Tab Intact
green
White
Neutral
Side of
Receptacle
120 VAC - Black
Neutral - White
ground - green
j-BOx / RECEPTACLE
WIRINg
120V, 60HZ, 1PH
junction Box
field Wired
factory Wired
(Power Supply
Unswitched)
CAUTION
ground supply lead must be con-
nected to the wire attached to the
green ground screw located on the
outlet box. failure to do so will
result in a potential safety hazard.
The appliance must be electrically
grounded in accordance with local
codes or, in the absence of local
codes, the National Electrical Code,
ANSI/NfPA 70, latest edition (in
Canada, the current CSA C22.1
Canadian Electrical Code).
WARNINg
Electrical grounding Instructions
This appliance is equipped with a three-prong (grounding) plug for your
protection against shock hazard and should be plugged directly into
a properly grounded three-prong receptacle. dO NOT cut or remove
the grounding prong from the plug.
CAUTION: Label all wires prior to discon-
nection when servicing controls. Wiring
errors can cause improper and dangerous
operation.
ATTENTION: Au moment de l'entretien
des commandes, étiquetez tous les fils
avant de les débrancher. des erreurs
de cáblage peu-vent entraîner un fonc-
tionnement inadéquat et dangereux.
Verify proper operation after servicing.
S’assurer que l'appareil fonctionne adé-
quatement une fois l'entretien terminé.
fIELd WIRINg
0.375"
0.375"
0.25"
Ø
NOT FOR USE WITH SOLID FUEL
CAUTION:
Hot while in operation. Do not
touch. Severe Burns may result. Keep children, clothing,
furniture, gasoline and other liquids having flammable
vapors away.
CAUTION:
Do not operate the appliance with
factory installed refractory panel(s) removed, cracked or
broken. Replacement of the factory installed refractory
panel(s) should be completed by a licensed or qualified
service person.
WARNING:
Improper installation, adjustment,
alteration, service or maintenance can cause injury
or property damage. Refer to the owner’s information
manual provided with this appliance. For assistance
or additional information consult a qualified installer,
service agency or the gas supplier.
Due to high temperatures, keep children, and furniture
away.
Keep burner and control compartment clean. See
installation and operating instructions accompanying
appliance.
WARNING:
Do not connect 120 V AC to the control valve.
THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE
WITH LOCAL CODES, IF ANY; IF NONE, FOLLOW THE
NATIONAL FUEL GAS CODE, ANSI Z223.1, OR NATURAL
GAS AND PROPANE INSTALLATION CODE, CSA B149.1.
If not installed, and maintained in accordance with the
manufacturer's instructions, this product could expose
you to substances in fuel or fuel combustion which are
known to the state of California to cause cancer, birth
defects, or other reproductive harm.
* For a copy of the homeowner’s care and operation
manual, go to www.lennox.com or call 1-800-9-lennox.
DIRECT VENTED APPLIANCES MUST NOT BE OPERATED
WITHOUT THE FRONT GLASS PANEL(S) INSTALLED.
DO NOT OPERATE APPLIANCE WITH BROKEN,
CRACKED OR MISSING GLASS DOORS OR ENCLOSURE
PANEL(S).
P/N 580095-01
DFC WIRE HARNESS
PROFLAME DFC BOARD
UNIT MOUNTED
ROCKER SWITCH*
PILOT TUBE
FAN
POWER CORD
POWER CORD
CABLE HARNESS
HIGH-TEMP SLEEVE
FAN CONTROL
MODULE
WALL
RECEIVER
DIGIT
AL
FIREPLACE BURNER CONTROL
SPARK WIRE
CABLE
PILOT SENSOR
CABLE
IGNITER ROD
FLAME
SENSOR
PROFLAME
ELECTRONIC
VALVE
JUNCTION BOX
* Unit Mounted Rocker Switch
OFF (o) = Intermittent Pilot Mode
ON (-) = Standing Pilot Mode
Y
120V
Out
Fan
Power
Aux
Out
B
W G
C
A
V
0
2
1
Schematic Representation Only
PILOT BURNER
IGNITER-SENSOR
ASSEMBLY
B
B
Wiring Color Code
B = Black
BL = Blue
BR = Brown
G = Green
GY = Gray
O= Orange
PU = Purple
W = White
R = Red
P = Pink
Y = Yellow
O
W
W
W
Y
G
G
G
G
B, BR, Y
, O
P, BL
P, BL
R,PU,GY
NOTES:
1. If any of the original wire as supplied
must be replaced, use Type AWM 105°C
- 18 gage wire ONLY.
2. 120 VAC, 60 Hz - Less than 5 Amps.
CAUTION: label all wires prior to discon-
nection when servicing controls. Wiring
errors can cause improper and danger-
ous operation. Verify proper operation
after servicing.
ELECTRONIC
IGNITION WIRING
DIAGRAM
