manualshive.com logo in svg

Lennox Hearth Products RHAP42N, Installation Instructions Manual

Share
Download
Lennox Hearth Products RHAP42N Installation Instructions Manual Download Page 16

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

16

VENT RESTRICTOR  

REqUIREMENTS

Installation of the provided vent restrictor as-

sembly is required for the venting configura-

tions listed in 

Figure 24

.

The  Vent  Restrictor  Kit  (provided  with  the 

fireplace;  see 

Figure  23

)  includes  one  vent 

restrictor base, two wings, and four screws. 

1.  Refer to 

Figure 24

. 

  For venting configurations listed under 

“Setting 1”:

  Use the vent restrictor base only 

(no assembly is required).

  For venting configurations listed under 

"Setting 2" or "Setting 3":

  Use the four provided screws to attach 

the  two  wings  to  the  vent  restrictor 

base 

in the applicable position

.

2.  If  the  baffle  and  back  panel  are  already 

installed, remove them before proceeding. 

See 

Page 27

.

3.  Install  the  vent  restrictor  assembly  from 

inside  the  firebox.  With  the  flaps  on  the 

vent  restrictor  base  facing  UP,  carefully 

bend the flaps inward just enough to slide 

the  assembly  up  into  the  vent  collar,  as 

shown in 

Figure 25

)

.

  The vent restrictor is held in place by fric-

tion only.

The  entire  vent  restrictor  assembly  must 

be up inside the vent collar, with no portion 

showing inside the firebox.

Vent Restrictor kit

(provided with fireplace)

(1) Vent Restrictor Base

(2) Wings

(4) Screws

Figure 23

“flaps”

Figure 24

Setting 1 (Vent Restrictor Base only) is required for the following configurations:
• Horizontal termination with total vertical run of more than 6 ft.
• Vertical termination with total vertical run of 6–10 ft.

Setting 2 is required for the following configuration:
• Vertical termination with total vertical run of 10+–40 ft.

Setting 3 is required for the following configuration:
• Vertical termination with total vertical run of 40+–60 ft.

Figure 25: Vent Restrictor Installation

[DETAIL]

Vent 

Collar

firebox

Vent Restrictor Assembly Settings and Applications

Vent 

Restrictor 

Assembly

(held in place  by 

friction only)

LENNOX HEARTH PRODUCTS  •  RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODELS RHAP42N & RHAP54N)  •  INSTALLATION INSTRUCTIONS

VENTINg INSTALLATION

(CONTINUEd)

Summary of Contents for RHAP42N











































Reviews:

No comments

Brands by name

Popular brands

Load more brands