Lehman Renegade 2009 Installation Instructions Manual Download Page 10 | Manualshive

Page: 10 / 42

background image

2009-2013

FLH

RENEGADE

TRIMMING

EXHAUST

NOTE: Trimming rear head pipes is more

convenient while swingarm is removed

from frame.

1. Remove LH and RH rear heat shields.
2.

See Fig. 4

. Using an appropriate cutting tool,

cut 1 5/8” from end of both rear head pipes.

3. Reinstall LH heat shield after cut. Shield will

be placed 1/4” to 1/2” forward to gain clear-
ance for extension pipe installation.

4. Install RH heat shield.

Fig. 4

REMOVING H-D SWINGARM

10

«
...
8
9
10
11
12
...
»

Summary of Contents for Renegade 2009











































Reviews:

No comments

Related manuals for Renegade 2009

Brand: AJP Pages: 191

Brand: Ducati Pages: 128

Mambo Evo PURE CARBON

Brand: LAZER Pages: 13

Brand: hepco & becker Pages: 4

Brand: Honda Pages: 556

Brand: MW TOOLS Pages: 9

TRACER MTT9K 2019

Brand: Yamaha Pages: 122

TT-R125(N) 2000

Brand: Yamaha Pages: 508

TT-R125(R) 2002

Brand: Yamaha Pages: 510

Brand: Yamaha Pages: 610

TT-R125(S) 2003

Brand: Yamaha Pages: 610

Brand: Yamaha Pages: 616

Brand: Yamaha Pages: 90

Brand: Wunderlich Pages: 2

Brand: Gemini Pages: 9

Brand: Petzl Pages: 4

Brand: Bikecomm Pages: 15

Brand: hepco & becker Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands