background image

2

MOUNTING AND WIRING

Installation shall be in accordance with all applicable regulations, wiring practices, and codes. 

Connect to a Class 2 power source only. 

•  Class 2 Device Wiring Only. – Do Not Reclassify and Install as Class 1, 3 or Power and Lighting 

Wiring. 

•  Wire connections shall be rated suitable for the wire size (lead and building wiring) employed.

The LMIO-101 is UL2043 Plenum rated.
All connections to the LMIO-101 are Class 2 low voltage.
If code requires that the LMIO-101 be mounted in an enclosure, it can be mounted inside a 4” x 4” 

junction box, inside a 21/8” deep (or deeper) 2-gang wall box, in a 3” or 4” octagonal box, or on a din 

rail inside a panel. 

Attach the LMRJ Cable

The DLM local network uses free topology low voltage wiring. The LMIO-101 can connect anywhere on the DLM local network.

RJ45 ports (2)

Configuration 

push button

LEDs (5)

DIP switches

Input/Output

Wiring Terminals

Configuration LED

Attach din rail clip

Option 1: Attach to din rail

Option 2: Mount to wall

Inside a 2-gang J-box

CAUTION:

 TO CONNECT A COMPUTER TO THE DLM LOCAL NETWORK USE THE LMCI-100.  

NEVER CONNECT THE DLM LOCAL NETWORK TO AN ETHERNET PORT

 – IT MAY 

DAMAGE COMPUTERS AND OTHER CONNECTED EQUIPMENT.

LMRJ Cables

Line Voltage

Room

Controller

Occupancy Sensor

Switch

LMIO-100 Series Digital

Input/Output Interface

Low Voltage Wires (2-10)

Loads

1

2

Input from Third Party Device

(example: time clock)

Output to Third Party Device 

(example: HVAC)

(3) N.C.

(normally closed)

(1) N.O.

(normally open)

To External

Device

Contacts rated at 1 amp @ 24V AC/DC

Isolated Relay

LMIO-101 Terminals

(2) COM

The isolated relay output is on 

terminals 1, 2 and 3. By default, the 

relay responds to a signal from any 

DLM sensor. See 

Isolated Relay 

Binding

 to change bound sensors.

Momentary Push Button Switch

LMIO-101 Terminals

 

ON

OFF

(5) +24VDC

(6) Input 1A

(8) Input 2A

or

(7) Input 1B

(9) Input 2B

or

NOTE: 

This is a toggling input

Press once

 = signal sent, the 

Blue LED corresponding to the 

input will be lit on the LMIO-101

Press again

 = the relinquish 

command is sent, the Blue LED 

corresponding to the input will be 

OFF on the LMIO-101

Momentary On/Momentary Off Switch

LMIO-101 Terminals

 

ON

OFF

(5) +24VDC

(6) Input 1A

(8) Input 2A

or

(7) Input 1B

(9) Input 2B

or

Contact Closure Options

(6, 7, or 8)

Input 1A, 1B or 2A

24VDC

from

3rd Party

Source

+

-

(5) +24VDC

(6, 7, or 8)

Input 1A, 1B or 2A

(4) Ground GND

LMIO-101 Terminals

TERMINAL CONNECTIONS

Summary of Contents for Wattstopper LMIO-101







Reviews: